Before Starting The Equipment; Operation; Cleaning, Maintenance And Ordering Spare Parts - EINHELL GE-GS 18 Li Traduction Du Mode D'emploi D'origine

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Changing the saw blade (Fig. 3a)
Warning!
Switch off the universal saw and pull out the
battery pack each time before doing any work on
the machine and changing the blade.
Open the cover (Fig. 3a/Item 7) by pressing it
together slightly at the front and then swinging it
up.
Turn the ring (8) on the blade holder (4) as
shown in Fig. 3a until the blade (6) lets itself be
slipped into the slot of the blade holder (4). When
you now let go of the ring (8) again, the ring (8)
should return to its starting position. If this fails to
happen, try turning the ring (8) by hand into its
starting position.
Now pull on the blade to check whether it is tightly
seated in the holder.
5.2 Fitting the branch jaw clamp (Fig. 3b/3c)
The branch jaw clamp (Fig. 1/Item 5) helps you to
guide the equipment when cutting branches. The
equipment can be used either with or without the
branch jaw clamp.
To fi t the branch jaw clamp, press the lock release
(Fig. 3b/Item 9) and push the branch jaw clamp
onto the soleplate from above. Make sure that the
two pins (Fig. 3c/Item 10) are correctly seated
in the related recesses (Fig. 3c/Item 11) of the
soleplate. Then check that the branch jaw clamp
is securely seated.

6. Operation

6.1 Charging the Li battery pack
The corresponding instructions can be found
in the original operating instructions for your
charger.
6.2 Battery capacity indicator (Fig. 4)
Press the battery capacity indicator switch (13).
The battery capacity indicator (12) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs lit:
The battery is fully charged.
Anl_GE_GS_18_Li_SPK7_USA.indb 13 Anl_GE_GS_18_Li_SPK7_USA.indb 13
EN
2 or 1 LED(s) lit:
The battery has an adequate remaining charge.
1 LED fl ashing:
The battery is empty, recharge the battery.
All LEDs fl ashing:
The battery pack has been deep-discharged and
is defective. Do not re-use or charge a defective
battery pack.
6.3 On/Off switch (Fig. 1/Item 1)
Switching on:
Press the locking button (2) and the On/Off switch
(1).
Infi nitely variable stroke speed control is possible
with the On/Off switch (1). The further you push
the switch, the higher the stroke speed.
Switching off :
Release the locking button (2) and the ON/OFF
switch (1) at the same time
6.4 Using as a universal jig saw (Fig. 5)
Place the universal saw, as shown in Fig. 5,
on the material you want to cut. Switch on the
universal saw and push the universal saw against
the material you want to cut. The cutting speed
must be adjusted to the material.
6.5 Using as a tree pruning saw (Fig. 6)
Place the tree pruning saw, as shown in Fig. 6,
on the branch you want to cut. Switch on the
tree pruning saw and push the tree pruning saw
against the branch you want to cut. The branch
jaw clamp will help you to guide the equipment
in a straight line. The cutting speed must be
adjusted to the material.
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
- 13 -
19.03.2020 10:28:24 19.03.2020 10:28:24