Technical Data; Before Starting The Equipment; Additional Handle - EINHELL TE-CS 18/150 Li Instructions D'origine

ces, be careful not to overheat the tips of the saw
blade and melt the plastic.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.

4. Technical data

Motor power supply: ............................... 18 V DC
Idling speed: ........................................4200 min
Cutting depth at 90°: ................................ 48 mm
Cutting depth at 45°: ................................ 32 mm
Saw blade: ..........................................Ø 150 mm
Blade holder: ....................................Ø 10/16 mm
Blade thickness: ...................................... 1.6 mm
Weight: .......................................................2.8 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ................. 105.17 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ................... 116.17 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Handle
Vibration emission value a
K uncertainty = 1.5 m/s

Additional handle

Vibration emission value a
K uncertainty = 1.5 m/s
Anl_TE_CS_18_150_Li_SPK13.indb 17 Anl_TE_CS_18_150_Li_SPK13.indb 17
-1
= 1.482 m/s
2
h, W
2
= 1.335 m/s
2
h, W
2
- 17 -
GB
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Setting the cutting depth (Figure 2/3)
•
Release the handle on the rear of the guard
hood for adjusting the cutting depth (4).
13.06.2022 08:42:53 13.06.2022 08:42:53