Candy DFI PLAN Mode D'emploi page 11

Operating the programmes
and special functions
Use in conjunction with programme guide
Setting a programme
Open the door press the button; the last
programme selected will appear on the display.
To set a new programme, press the Programme
Selection Button "P". When the required
programme is shown in the display, press the
"START" button. The time of the selected
programme (in hours and minutes) will start to
flash in the display.
Close the door and after an audible signal has
sounded (if it has not been deactivated) the
programme will start automatically.
Economy button
The "E" button reduces the temperature of the
water during the last rinse, provides an energy
saving of more than 20% and shortens the
cycle.
Recommended for evening washes when the
dishes are not required perfectly dry, straight
away.
HPS button (High Pressure System)
Your dishwasher is fitted with a two speed
motor. By pressing the HPS Button, the motor
operates at a higher speed which will result in
higher water pressure, to attack the dirt.
The HPS option is particularly suitable for
washing pans, pots and heavily soiled crockery.
Please Note:
This option must be selected before pres-
sing the START button.
"FLEXI HALF LOAD" Button
To ensure that your dishwasher meets all your
requirements, the "FLEXI HALF LOAD" option
button allows you to select:
Half Load Top Basket
a)
By selecting this option Dishes are
washed in the top basket and cutlery in
lower basket;
b) Half Load Lower Basket
By selecting this option Dishes are
washed in the lower basket only.
Interrupting a programme
It is not recommended that the door be opened
while a programme is running, and especially
not during the main wash phase and final
drying.
However, the appliance will stop automatically
when the door is opened.
At this point the various wash options can be
programmed or cancelled. The current program-
me can also be cancelled.
If, the door is opened during a programme, the
symbol for that programme will flash in the
display and the machine stops.
Please Note:
If you open the door during the drying cycle
an audible audio signal advises you that the
drying cycle has not yet completed.
To restart the machine, press the "START" button
and the time remaining for the programme will
flash. Now close the door.
If you wish to cancel or change a programme
that is running, carry out the following:
open the door keep the "START" button
pressed in until the number of the
programme stops flashing.
programme can now be set.
NB: If, on pressing the "START" button the
symbol "00" starts to flash on the display, it
means that there is water in the machine.
Close the door to allow the water to be
discharged and wait for the audible signal, after
which the new programme can be set.
Before starting a new programme, you should
check that there is still detergent in the dispenser.
If necessary, top up the dispenser.
End of programme
The end of the programme is indicated by an
audible signal (if it has not been deactivated).
When the door is opened the number of the
programme that has just finished will appear on
the display.
Important:
If the programme shown in the display starts
to flash and the machine will not let any more
programmes be selected, press the "START"
button and keep this button pressed until the
display stops flashing.
20
Delay Start programme button
To set the delay start programme press the
button.
On the first press the current setting appears on
the display. Each time the button is pressed the
delayed time in one hour increments increases,
up to a maximum of 19 hours.
Once set, wait until the selected time is confirmed
when it appears in the display. Press the "START"
button to start the countdown. If the countdown
has not already been activated, the delay start
can be cancelled by pressing the
until the selected programme appears on the
display.
The delay start can be cancelled at any time
simply by keeping the "START" button pressed
in until the required wash cycle appears on the
display.
If you wish to see which programme has been
selected, press the "Programme Selection"
button "P".
A new NB: If the door is opened during the countdown,
for example to select one of the options (or to
add more dishes), the "START" button should
be pressed before closing the door again, in
order to restart the countdown.
The Dishwasher is able to self-assess a number of problems. The problem will
be illustrated in the display window and by an audible signal.
PROBLEMS AUTOMATICALLY SIGNED
PROBLEM
Display shows E1.
Display shows E2.
Display shows E3.
Display shows E4.
Activating and deactivating the audible
signal
The audible signal function can be deactivated
in the following way:
keep the Programme Selection Button (P)
pressed in for a few seconds and at the same
time press the stop/start button
symbol "b1" appears on the display the audible
signal is activated. Press the
selection button (P) again and the symbol "b0"
will appear which means that the audible signal
has been deactivated.
button
An audible signal sounds to indicate that the
setting has been stored in memory.
Attention
This dishwasher is
anti-overflow safety device which works even
when power is off, and if the water level is too
high, the supply will automatically be closed off.
Important
To ensure the correct operation of the
anti-overflow safety device, it is recommended
not to move or to tilt the dishwasher during
operation.
If it is necessary to move or to tilt the
dishwasher, first make sure the washing cycle is
finished and that no water is left in the tank.
CAUSE
Water supply switched off.
Switch off appliance.
Turn on water supply.
Reset the cycle.
Problem with electronic temperature
Call Service for assistance.
control.
The Water Heater Element does not
Clean the Filter Mesh and if the
work properly or the filter mesh is
problem continues please contact
blocked.
Service.
The appliance does not discharge
Check :
• That the discharge hose is not
water.
bent
• Syphon is not blocked
• Filters are not blocked
21
; if the
programme
equipped with an
REMEDY