Bosch GDM 13-34 Professional Notice Originale page 8

OBJ_BUCH-936-006.book Page 8 Tuesday, September 26, 2017 12:39 PM
8 | English
Technical Data
Masonry Saw
Article number
Rated power input
Rated speed
Max. diameter for diamond cutting discs
Cutting discs width, min.
Cutting discs width, max.
Mounting bore
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
Weight according to EPTA-Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Assembly
 Before any work on the machine itself, pull the mains
plug.
Dust Extraction
 Dust from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dust can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dust, such as oak or beech dust, is considered car-
cinogenic, especially in connection with wood-treatment
additives (chromate, wood preservative). Materials con-
taining asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Mounting/Replacing the Diamond Cutting Disc
(see figure A)
 When mounting and replacing diamond cutting discs, it
is recommended to wear protective gloves.
 Diamond cutting discs become very hot during opera-
tion; do not touch them until they have cooled down.
 Always use a correctly sized diamond cutting disc with
the fitting mounting hole that corresponds with the
information listed in the technical data.
 Use only diamond-tipped cutting discs. Segmented
diamond wheels may only have negative cutting angles
and slots between the segments to a maximum of
10 mm.
Mounting the Diamond Cutting Disc
Clean the diamond cutting disc 15 and all clamping parts to
be mounted.
Mount the mounting flange 14 onto the drive spindle 13.
1 609 92A 41D | (26.9.17)
GDM 13-34
3 601 36A 2..
W 1300
-1
min 12000
mm 114
mm 1.6
mm 2.4
mm 20
mm 34
mm 22
kg 2.8
/II
Place the diamond cutting disc 15 onto the mounting flange
14. The direction arrow on the diamond cutting disc 15 and
the direction-of-rotation arrow on the blade guard 6 must
correspond.
Mount the clamping flange 16 and screw in the clamping bolt
18.
Hold the clamping flange 16 with the ring spanner 17 and
tighten the clamping bolt 18 with the hex key 19.
Removal of the Diamond Cutting Disc
Hold the clamping flange 16 with the ring spanner 17 and
loosen the clamping bolt 18 with the hex key 19.
Remove the clamping flange 16 and diamond cutting disc 15
from the drive spindle 13.
Operation
Operating Modes
 Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Angle (see figure B)
Loosen wing bolt 9. Tilt the machine sidewards until the de-
sired cutting angle is set on the scale 11. Tighten wing bolt 9
again.
Note: For bevel cuts, the cutting depth is smaller than the
setting indicated on the cutting-depth scale 3.
Pre-selecting the Cutting Depth (see figure C)
 The cutting depth may only be pre-selected when the
machine is switched off.
Adapt the cutting depth to the thickness of the workpiece. For
optimum results, the diamond cutting disc must protrude
approx. 2 mm out of the material.
Loosen wing bolt 4. For a smaller cutting depth, pull the
machine from the base plate 10; for a larger cutting depth,
push the machine toward the base plate 10. Adjust the
desired cutting depth at the cutting-depth scale 3. Tighten
wing bolt 4 again.
GDM 13-34
3 601 36A 2B0
1300
12000
114
1.6
2.4
15
34
22
2.8
/II
Bosch Power Tools