Ideal Standard ULTRA FLAT S Mode D'emploi page 9

UK
USE AND MAINTENANCE INFORMATION FOR THE USER
THE PRODUCT IS TO BE USED FOR PERSONAL HYGIENE AT ROOM TEMPERATURE, MEANING BETWEEN 10°C AND 30°C. SHOWERING AT A TEMPERATURE
ABOVE 40°C IS NOT RECOMMENDED.
NOTE: USING THE SHOWER TRAY WITH HOT WATER ABOVE ABOVE 55°C OVER A LONG PERIOD OF TIME MAY CAUSE DISCOLORATION.
THE MANUFACTURER SHALL NOT BE HELD LIABLE FOR DAMAGE CAUSED BY INCORRECT USE OF THE PRODUCT.
ULTRA FLAT S CHARACTERISTICS
ULTRA FLAT S IS A COMPOSITE MATERIAL, MADE UP OF NATURAL MINERALS AND RESINS. IT IS COATED WITH A TECHNICAL VARNISH WITH A MATT FINISH.
THIS COATING 800 1000 µM HAS EXCELLENT RESISTANCE PROPERTIES AND THE SURFACE IS FULLY REPAIRABLE.
DAILY MAINTENANCE
TAKING CARE OF ULTRA FLAT S IS QUICK AND SIMPLE. ALL YOU NEED TO DO IS CLEAN THE SURFACE WITH SOAPY WATER OR A NORMAL DETERGENT TO
REMOVE THE MAJORITY OF STAINS AND DIRT THAT MAY HAVE BUILT UPEPOSITED.
ABRASIVE OR GEL DETERGENTS USED WITH AN ABRASIVE SPONGE SUCH AS SCOTCH BRITE® ARE PARTICULARLY RECOMMENDED. RINSE THE TREATED
AREA AFTERWARDS. THIS HELPS TO MAINTAIN THE ORIGINAL MATT FINISH THAT DISTINGUISHES ULTRA FLAT S.
GRID
IF THE DRAIN IS CLOGGED IT CAN BE UNCLOGGED BY USE OF LIQUIDS OR REAGENTS IT IS MANDATORY TO REMOVE THE GRID TO AVOID POSSIBLE
DAMAGES. THE GRID MUST BE PUT IN ITS ORIGINALLY POSITION AFTER CONCLUDING THE CLEANING OPERATION.
HOW TO PREVENT DAMAGE
THE SURFACE IS GENERALLY RESISTANT TO STAINS; NONETHELESS, USE OF AGGRESSIVE CHEMICALS IS NOT RECOMMENDED. THESE INCLUDE: ACETONE,
TRICHLOROETHYLENE, STRONG ACIDS HYDROCHLORIC ACID, ETC. , STRONG BASES SODIUM HYDROXIDE, ETC. , INDUSTRIAL DETERGENTS AND
VARNISHING SOLVENTS. DO NOT USE METAL SCRAPERS, IRON BRUSHES OR OTHER DOMESTIC METAL TOOLS TO REMOVE STAINS, VARNISH, SEALANT OR
SIMILAR. SOME SUBSTANCES SUCH AS INK, COSMETICS AND DYES MAY LEAVE COLOURANT ON THE SURFACE OF ULTRA FLAT S WHERE THERE IS
PROLONGED CONTACT. THE SAME APPLIES FOR LIT CIGARETTES. THIS CAN BE REMOVED BY FOLLOWING THE INSTRUCTIONS BELOW. REMOVING
STUBBORN STAINS, SCRATCHES AND BURNS ULTRA FLAT S CAN BE RESTORED TO ITS ORIGINAL STATE FOLLOWING SURFACE DAMAGE SUCH AS SCRAPES,
CIGARETTE BURNS AND STUBBORN STAINS SIMPLY BY FOLLOWING THESE INSTRUCTIONS. FOR MINOR DAMAGE, USE A SCOTCH BRITE® 3M REGISTERED
TRADEMARK ABRASIVE SPONGE AND A STANDARD ABRASIVE DETERGENT. IF THE MARK IS STILL VISIBLE, CLEAN AGAIN FINISHING WITH VERY FINE
SANDPAPER.
WARRANTY
THIS PRODUCT HAS BEEN MANUFACTURED WITH TOP QUALITY MATERIALS AND COMPONENTS AND HAS UNDERGONE THE TESTS REQUIRED BY THE
MANUFACTURER'S CERTIFICATION STANDARDS AND BY APPLICABLE NATIONAL AND EUROPEAN STANDARDS. PRODUCT WARRANTY TAKES EFFECT AS OF
THE PURCHASE DATE OF THE PRODUCT, AS SHOWN ON THE INVOICE OR RECEIPT AND FOR THE PERIOD GRANTED UNDER APPLICABLE LAW. PRODUCT
WARRANTY GRANTED BY LAW ONLY COVERS DEFECTS APPEARANCE, DIMENSION, OPERATION EXISTING AT THE TIME OF DELIVERY RESULTING FROM
MANUFACTURING ERRORS, AS VERIFIED AND CONFIRMED BY THE MANUFACTURER'S AFTER SALES SERVICE TECHNICAL STAFF.
THE WARRANTY IS VALID WHERE:
• INSTALLATION HAS BEEN PERFORMED TO A HIGH STANDARD WITH THE SHOWER TRAY SQUARE WITH THE WALLS AND THE FLOOR LEVEL.
• THE PRODUCT HAS BEEN CHECKED BEFORE INSTALLATION.
• LEAKS HAVE BEEN CHECKED FOR DURING INSTALLATION
• PRODUCT MAINTENANCE AND CLEANING HAVE BEEN PERFORMED IN LINE WITH THE INSTRUCTIONS IN THE MAINTENANCE AND CARE MANUAL.
THE WARRANTY IS NOT VALID WHERE:
• THE USE AND INSTALLATION INSTRUCTIONS LISTED HERE HAVE NOT BEEN RESPECTED.
• MODIFICATIONS AND CUSTOMISATION ARE PERFORMED BY THE INSTALLER/USER WITHOUT THE MANUFACTURER'S AUTHORISATION.
• BREAKAGE/ACCIDENTAL DAMAGE IS CAUSED BY KNOCKS/IMPROPER USE.
• IT IS A CASE OF NORMAL PRODUCT WEAR.
• DAMAGE IS CAUSED BY DISASTERS SUCH AS FIRES OR NATURAL DISASTERS, INCLUDING FLOODS, EARTHQUAKES, ETC.
THE EQUIPMENT MUST BE INSTALLED BY QUALIFIED PERSONNEL IN COMPLIANCE WITH THE CURRENT STANDARDS IN FORCE RELEVANT TO CIVIL ELECTRIC
AND HYDRAULIC SYSTEMS.
ECOLOGICAL NOTES
UPON COMPLETION OF INSTALLATION, PLEASE REMEMBER TO DISPOSE OF THE PACKAGING AND ASSEMBLY WASTE IN ACCORDANCE WITH
THE REGULATIONS IN EFFECT IN THE COUNTRY WHERE THE PRODUCT WILL BE USED.
| 9