glass 1989 AZULEJO Notice D'installation page 10

EN
• Pay maximum attention when the surrounding floor is wet,
as there will be a potentially high risk of slipping. this, mainly,
when using soaps, shampoos, clearing detergents, etc..
• It is not advisable to use the shower cabin with water that is too
hot. Use water with a maximum temperature of 38°C.
• This product is not intended to be used by persons (including
children) with reduced physical, sensory or mental capabilities
or lack of experience or knowledge, unless they have been
given appropriate supervision or instruction concerning use
of the appliance by a person responsible for their safety.
• WARNING: children may use the product unsupervised only
when its operation has been clearly explained to them and
they are able to use it safely while recognising the dangers of
misuse.
All measurements are in mm.
PRE-INSTALLATION REQUIREMENTS
To prevent damaging the mixer parts, place a filter upstream of
the mixer.
TECHNICAL INFORMATION:
• Minimum flow pressure:
• Operating pressure:
• Recommended operating pressure:
• Hot water temperature:
The product's supporting structure is metallic. An efficient
ground system is therefore required, with sensitivity meeting
the relevant standards.
GROUNDWIRE.
The ground wire must be connected and fixed permanently
to the electrical system.
EQUIPOTENTIAL CONNECTION.
The equipment must be connected to the equipotential
system of the room and duly fastened to its terminal to be
found in the product.
The following accessories
manufacturer) are required for installation:
a) Fittings to connect the mixer to the domestic water mains
(connection to mixer via ½" fittings).
ROUTINE AND
SPECIAL MAINTENANCE
Use water up to a maximum of 60°C to maintain the shine of the
product over the years.
Use a soft sponge dampened with water and non-abrasive
neutral liquid detergents
for cleaning.
After cleaning, rinse thoroughly with plenty of water to
remove all traces of detergent and dry with a soft cloth.
Avoid:
– cleaning materials which contain hydrochloric acid, formic acid,
bleach or acetic acid, as they can cause considerable damage.
– synthetic fibre cloths, scouring pads, metal pads, abrasive
detergents, alcohol, acids for domestic use, acetone or other
solvents which damage the surface.
–the build-up of limescale by cleaning regularly.
IMPORTANT:
Residues of toiletries such as liquid soaps, shampoos and shower
gels, hair dyes, perfumes, aftershave and nail varnish can also
cause damage.
Rinse thoroughly with plenty of water to remove all traces
of detergent.
150 kPa (1,5 bar)
350 kPa (max 3,5 bar)
250 kPa (2,5 bar)
max 60°C
(not supplied by the
Limescale can be removed from water jet nozzles simply by
rubbing.
Special maintenance must be carried out by qualified
personnel.
In case of failures or malfunctioning of the product, contact
only authorised technicians to avoid losing warranty rights. The
manufacturer shall not be held responsible for any damage
caused by products that have been tampered with or repaired
wrongly.
THERMOSTATIC MIXER CLEANING.
In order for the mixer to operate properly, it is recommended
to keep the cartridge clean by performing periodic
maintenance.
Contact a qualified technician to check the status of the
thermostatic cartridge, should it be difficult to adjust the
temperature, remove the handle (foreign bodies) and unscrew
the cartridge. Check the condition of the gaskets, remove traces
of dirt and limestone with vinegar. Reposition the cartridge with
the aid of Vaseline. Calibrate the thermostatic mixer. In the
event that, by carrying out the operations indicated, the problem
is not resolved, and it is required to replace the components of
the thermostat, always use original spare parts by contacting
the nearest support centre or the manufacturer directly.
TROUBLESHOOTING
In the event of abnormalities run the following checklist.
All hydraulic connection checkup must be performed by a
hydraulic installation technician.
If the water is slow to drain away, check that the drain is not
blocked.
If the product does not dispense water, check that:
- There is water in the main pipe.
- The diverter is correctly set.
- There are no impurity into the pipes that prevent normal
water flow.
If the above operations do not solve the problem, contact your
nearest service centre or the company.
10