Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Table of Contents
1.
Getting to Know Your Saw .......13
2.
Please Read First! .....................14
3.
Safety .........................................14
3.1 Specified conditions of use .........14
3.2 General safety instructions..........14
saw..............................................15
these instructions ........................15
3.5 Safety devices.............................15
4.
Special Product Features .........16
5.
Transportation...........................16
6.
Operating Elements ..................16
7.
Initial Operation.........................17
7.1 Installation ...................................17
blade guard installation. ..............17
7.3 Connection of dust collector........17
7.4 Mains connection ........................18
8.
Operation ...................................18
8.1 Sawing ........................................18
9.
Care and Maintenance ..............18
9.1 Saw blade change.......................18
9.2 Scale setting................................19
9.3 Mitre fence adjustment................19
9.4 Blade tilt stop setting ...................19
9.5 Saw cleaning...............................19
9.6 Machine storage..........................19
9.7 Maintenance................................20
10. Tips and Tricks..........................20
11. Available Accessories .........20/52
12. Repairs .......................................20
13. Environmetal Protection...........20
14. Trouble Shooting ......................20
15. Technical Specifications ..........21
2. Please Read First!
•
Read these instructions before use.
Pay special attention to the safety
instructions.
•
If you notice transport damage while
unpacking,
notify
your
immediately. Do not operate the
saw!
•
Dispose of the packing in an envi-
ronmentally friendly manner. Take
to a proper collecting point.
•
Keep these instructions for refer-
ence on any issues you may be
uncertain about.
•
If you lend or sell this machine be
sure to have the instructions go with
it.
14
3. Safety
3.1
Specified conditions of
use
This machine is intended to rip and
crosscut grown timber, faced boards,
chip board and wood-core plywood
sheets, and similar wood-derived materi-
als.
Metals can only be cut with the following
restrictions:
− with suitable saw blade only
(see "Available Accessories")
− non-ferrous metals only
(no hard or hardened metals)
Do not cut round stock without suitable
jigs or fixtures. The rotating saw blade
could turn the workpiece.
When sawing thin stock layed on edge,
a suitable guide must be used for firm
support.
Use of wobble saw blades is not permit-
ted on this machine.
A
Danger!
Any other use is not as speci-
fied.
Use not as specified, alteration of the
electric tool or use of parts that are not
approved by the equipment manufac-
turer can cause unforeseeable damage!
3.2
General safety instruc-
tions
•
When using this tool observe the fol-
lowing
exclude the risk of personal injury or
material damage.
•
Please also observe the special
safety instructions in the respective
chapters.
•
Where applicable, follow the legal
directives or regulations for the pre-
vention of accidents pertaining to
the use of circular saws.
A
General hazards!
•
Keep your work area tidy - a messy
work area invites accidents.
•
Be alert. Know what you are doing.
supplier
Set out to work with reason. Do not
operate tool while under the influence
of drugs, alcohol or medication.
•
Consider environmental conditions:
keep work area well lighted.
•
Prevent adverse body positions.
Ensure firm footing and keep your
balance at all times.
•
Use suitable workpiece supports
when cutting long stock.
•
Do not operate the tool near inflam-
mable liquids or gases.
•
The saw shall only be started and
operated by persons familiar with
safety
instructions,
to
circular saws and who are at any
time aware of the dangers associ-
ated with the operation of such tool.
Persons under 18 years of age shall
use this tool only in the course of
their vocational training, under the
supervision of an instructor.
•
Keep bystanders, particularly chil-
dren, out of the danger zone. Do not
permit other persons to touch the
tool or power cable while it is run-
ning.
•
Do not overload tool - use it only
within the performance range it was
designed for (see "Technical Speci-
fications").
B
Danger! Risk of electric shock!
•
Do not expose tool to rain.
Do not operate tool in damp or wet
environment.
Prevent body contact with earthed
objects such as radiators, pipes,
cooking stoves, refrigerators when
operating this tool.
•
Do not use the power cable for pur-
poses it is not intended for.
A
Risk of personal injury and
crushing by moving parts!
•
Do not operate the tool without
installed guards.
•
Always keep sufficient distance to
the saw blade. Use suitable feeding
aids, if necessary. Keep sufficient
distance
to
driven
when operating the electric tool.
•
Wait for the saw blade to come to a
complete stop before removing cut-
offs, scrap, etc. from the work area.
•
Do not attempt to stop the saw
blade by pushing the workpiece
against its side.
•
Ensure the tool is disconnected from
power before servicing.
•
Ensure that when switching on (e.g.
after servicing) no tools or loose
parts are left on or in the tool.
•
Turn power off if the tool is not used.
A
Cutting hazard, even with the
cutting tool at standstill!
•
Wear gloves when changing cutting
tools.
•
Store saw blade in such manner that
nobody will get hurt.
A
Risk of kickback (workpiece is
caught by the saw blade and thrown
against the operator):
•
Always work with a properly set riv-
ing knife.
•
The riving knife and the saw blade
used must match: the riving knife
components
Publicité
Chapitres
Table des Matières
