Introduction; Device Description; Scope Of Delivery - Scheppach SG2000 Traduction Du Manuel D'origine

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope you have a lot of fun and success using your
new machine.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• improper handling,
• noncompliance of the operating instructions,
• repairs by third parties, not by authorized service
technicians,
• installation and replacement of non-original spare
parts,
• non-intended use,
We recommend:
that you read through the entire operating instruc-
tions before putting the machine into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications. The operating instructions contain impor-
tant notes on how you work with the machine safely,
expertly, and economically, and how you can avoid
hazards, save repair costs, reduce downtime and in-
crease the reliability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country's applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed con-
scientiously. Only persons who have been trained in
the use of the machine and have been informed of
the various dangers may work with the machine. The
required minimum age must be observed. In addition
to the safety requirements in these operating instruc-
tions and your country's applicable regulations, you
should observe the generally recognized technical
rules concerning the operation of identically con-
structed devices.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
2. Device description (Fig. 1-3)
1. Carrying handle
2. Fuel tank cap with ventilation
3. Fuel tap
4. Starter pull cord
5. Engine cover
6. Spark plug cover
7. Fuel pump
8. Earthing connection
9. Energy saving switch
10. 230 V ~ - socket outlets (2x)
11. 12 V d.c. safety release
12. 12 V d.c. connection
13. Oil warning display
14. Overload display
15. Operating display
16. Choke le ver
17. Spark plug spanner
18. Adapter cable with 12V terminals
19. 230 V plug
20. Oil measuring cup
A Vent „ON"
B Vent „OFF"
C Fuel line
D Oil filler plug
E Air filter cover
F Prefilter
G Fine filter
H Spark plug
I Ignition cable

3. Scope of delivery

• SG2000, manual, spark plug wrench, 230V plug,
Adapter cable with 12V terminals, Oil funnel
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available)
• Check that the delivery is complete.
• Check the device and its spare parts for possible
damage caused by transportation. In the event of
complaints, you must contact the distributor with-
out delay. Claims at a later stage will not be ac-
cepted.
• If possible, store the packaging until the warranty
period has expired
• Before handling the device, make yourself familiar
with it by reading the operating instructions.
• For accessories, consumables and spare parts,
only use original parts. Spare parts are available
from your stockist.
• Include our item number, the device model and
year of manufacture in your order.
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts!
m DANGER
There is a risk of swallowing and suffocation!
GB
17 / 92