Cool Mode; Heat Mode; Fan Mode - Qlima P522 Manuel D'utilisation

Masquer les pouces Voir aussi pour P522:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 15
to make the appliance turn on. The last function active when it was turned
off will appear.
G
Never turn the appliance off by unplugging from the mains. Always press
the button
, then wait for a few minutes before unplugging. This
allows the appliance to perform a cycle of checks to verify operation.
DESCRIPTION OF THE DISPLAY SCREEN
Plug into the mains socket, then the appliance is standby. Press the
to make the appliance turn on. The last function active when it was turned
off will appear.

COOL MODE

Ideal for hot muggy weather when you need to cooling and dehumidify the
room.
To set this mode correctly:
• Press the M button a number of times until the
• Select the target temperature18°C-35°C(64 °F-90°F) by pressing the /\ or
v button until the corresponding value is displayed.
• Select the required fan speed by pressing the
Three speeds are available:
Maximum speed: for maximum fan power
Medium speed: reduces noise levels but still maintains a good level of comfort
Low speed: for silent operation
The most suitable temperature for the room during the summer varies from 24°C
to 27°C(75°F to 81°F ). You are recommended, however, not to set a temperature
much below the outdoor temperature. The fan speed difference is more
noticeable when the appliance is under FAN mode but may not be noticeable
under COOL mode.

HEAT MODE

* means only the heat pump model have this function.
To set this mode correctly:
• Press the M button a number of times until the
• Select the target temperature 13"C-27°C(55 °F-81°F) by pressing the /\ orV
button until the corresponding value is displayed.
• Select the required fan speed by pressing the
Three speeds are available:
Maximum speed: for maximum fan power
Medium speed: reduces noise levels but still maintains a good level of comfort
Low speed: for silent operation
• Water is removed from the air and collected in the tank.
• When the tank is full, the appliance shuts down and "
on the display. The tank cap must be extracted and emptied. Run off all
4
54
button
symbol appears.
button.
symbol appears.
button.
" (full tank) appears
water left into a basin. When all the water has been drained, put the cap
back in place.
• When the tank has been emptied, the appliance starts up again.
N.B.: -When operating in very cold rooms, the appliance defreezes automatically,
momentarily interrupting normal operation. "
During this operation, it is normal for the noise made by the appliance to
change.
- In this mode, you may have to wait for a few minutes before the appliance
starts giving out hot air.
- In this mode, the fan may operate for short periods, even though the set
temperature has already been reached.

FAN MODE

When using the appliance in this mode, the air hose does notneed to be
attached.
• Press the M button a number of times until the
• Select the required fan speed by pressing the
Three speeds are available:
Three speeds are available:
Maximum speed: for maximum fan power
Medium speed: reduces noise levels but still maintains a good level of comfort
Low speed: for silent operation
DRY MODE
Ideal to reduce room humidity (spring and autumn, damp roomsrainy periods,
etc).
In dry mode, the appliance should be prepared in the same way as for cool
mode, with the air exhaust hose attached to enable the moisture to be
discharged outside.
To set this mode correctly:
• Press the M button a number of times until thedh symbol appears.
• Select the required fan speed by pressing the
Three speeds are available:
Maximum speed: to achieve the best dehumidify effect.
Medium speed: can reduce noise level but still maintances a better dehumidify
effect.
Low speed: for silent operation but weaken the dehumidify effect relatively.
SWITCH THE UNIT OF TEMPERATURE
When the appliance is standby, press the M button 20 seconds, then you can
change the unit of temperature.
For example:
Before change, in cool mode, the screen display like fig 1.
After change, in cool mode, the screen display like fig 2.
" appears on the display.
symbol appears.
button.
button.
4
55

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

P528P534Ph534

Table des Matières