Publicité
Les langues disponibles
Les langues disponibles
o)
Do not work on two workpieces at the same time.
p)
It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
q)
Keep the device away from sources of fire and heat.
r)
When working with the machine, pay special attention
to the kickback phenomenon, which is a sudden
reaction of the machine to the rotating disc being
blocked. The consequence of locking the rotating tool
is the jerk of the machine in the direction opposite to
the disc rotation. The kickback is a consequence of
improper use of the machine.
s)
Do not use parts or accessories not designed to work
with this device, unless they have been indicated by
the manufacturer as compatible.
t)
The rated speed of the accessory must be at least
equal to the maximum speed of the device, otherwise
accessories that rotate faster than the rated speed
may be destroyed.
u)
Parameters of used accessories (discs, sandpaper)
must be in accordance with the technical parameters
indicated in the table; otherwise the device may not
be properly secured and controlled.
v)
Attaching the accessories must be compatible with
the device's mounting hardware.
w)
Accessories not suited to the device's mounting
hardware may lose their stability, over-vibrate, and
the control over them may be lost.
x)
Do not use accessories which are damaged. Before
every use, check their condition in terms of chips,
cracks, tears or excessive wear.
y)
Should you drop the device, check it for damage.
After inspection and replacement of damaged
elements, set the device securely with respect to the
user and the third parties so that all are away from the
rotating elements. Turn on the device at the highest
speed and allow continuous operation for about 1
minute. Damaged parts during this procedure ought
to fall apart.
z)
Hold the device touching only the insulated handle
surfaces. It is possible you may come across hidden
wiring or hit your own power cord while working.
Contact with the power cord may cause electric shock.
aa)
Keep the power cord away from rotating parts. If you
lose control over the device, the cord may be cut or
caught and a limb may be pulled into the rotating
accessories.
bb)
Do not put the device away until it stops working and
is switched off. Rotating elements may come into
contact with the surface and rip out the equipment
from the user's grip.
cc)
Do not operate the device when worn on the body.
Accidental contact of rotating accessories with clothes
you wear with may cause the rotating elements come
dangerously close to your body.
dd)
Do not use accessories that require the use of cooling
substances. The use of water or liquid coolant may
cause electric shock.
ee)
Hold the device firmly so that you can resist the force
in the event of a kickback. Use the auxiliary handle, if
available, to obtain maximum control over kickback or
torque during start-up.
ff)
Keep away from rotating parts, those parts may
bounce towards your body.
gg)
Do not position yourself body in the direction in
which the kickback can occur. The kickback will direct
the device in the direction opposite to the rotation.
10
hh)
Pay special attention when working corners or sharp
edges. Avoid locking and contact with random objects
while working. It may result in losing control over the
device.
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there is
still a slight risk of accident or injury when using the
device. Stay alert and use common sense when using
the device.
3. USE GUIDELINES
The device is used for sanding walls and ceilings made of
plasterboard or plaster.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
2 4
6
8
1
3
5
7
10
1.
Motor
2.
Speed controller
3.
ON / OFF button
4.
Main handle
5.
Auxiliary handle
6.
Power cable
7.
Suction pipe
8.
Suction bag
9.
Sanding pad (round)
10.
Sanding pad (triangular)
3.2. PREPARING FOR USE
ASSEMBLING THE DEVICE
1.
Suction connection
Before starting work, connect the dust bag as shown.
NOTE: Failure to connect the dust bag will increase the level
of dust in the air. Continuous and prolonged exposure to
high levels of dust in the air may affect the operator's
respiratory function.
NOTE: It is recommended to empty the dust bag when it
is half full.
Rev. 04.06.2020
2.
Sanding pad and sandpaper
Before starting work, choose a sanding pad and
install it according to the instructions below. Install
the sanding paper with the appropriate gradation
(depending on the surface to be worked on and the
desired result).
Sanding pad replacement:
1)
Press the quick assembly buttons to release the
mounted plate.
2)
Place the second pad in front of the device, align the
holes with the device body as shown below.
3)
Press the device against the substrate, the quick
assembly buttons will automatically lock the pad.
3.3. DEVICE USE
3.3.1. SPEED CONTROL
The device has smooth speed regulation. To adjust the
speed, use the control knob (see section 3.1., Item 2) to
select the appropriate speed: Min, 1, 2, 3, 4, 5, Max.
3.3.2. STARTING AND STOPPING THE DEVICE
START
1)
Press the On / Off button
2)
Press the trigger while holding the On / Off button
3)
Release the On / Off button
4)
Set the correct speed
STOP
5)
Set the speed to the minimum
6)
Press the On / Off button
7)
Release the trigger and the On / Off button
Rev. 04.06.2020
3.3.3. TIPS FOR WORKING WITH THE DEVICE
•
Always hold the device with two hands during
operation!
•
Before starting work, clean the wall of any protruding
nails, screws and electrical components as they may
damage the device and cause danger for the operator.
•
Press the pad lightly during work so that the entire
pad adheres evenly to the surface. Excessive pressure
may cause visible traces and uneven surface.
•
Bear in mind that the efficiency and quality of work
depend mainly on the correct abrasive material and
the rotational speed which is selected according to
the type of surface being worked on.
•
When finishing work, it is recommended to hold the
device against the sanded surface to collect all the
dust.
3.4. CLEANING AND MAINTENANCE
a)
Unplug the mains plug and allow the device to cool
completely before each cleaning, adjustment or
replacement of accessories, or if the device is not
being used. Wait for the rotating elements to stop.
b)
Use only non-corrosive cleaners to clean the surface.
c)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
d)
Do not spray the device with a water jet or submerge
it in water.
e)
Do not allow water to get inside the device through
vents in the housing of the device.
f)
Clean the vents with a brush and compressed air.
g)
The device must be regularly inspected to check its
technical efficiency and spot any damage.
h)
Use a soft cloth for cleaning.
i)
Do not clean the device with an acidic substance,
agents of medical purposes, thinners, fuel, oils or
other chemical substances because it may damage
the device.
REPLACING THE CARBON BRUSH
The carbon brush wears out after about 45 hours of
operation. In this case, replace it with a new one. To do this,
unscrew the brush cover with a screwdriver.
Take the brush out of the holder, put a new brush in the
holder and screw on the cover.
DISPOSING OF USED DEVICES
Do not dispose of this device in municipal waste systems.
Hand it over to an electric and electrical device recycling
and collection point. Check the symbol on the product,
instruction manual and packaging. The plastics used
to construct the device can be recycled in accordance
with their markings. By choosing to recycle you are
making a significant contribution to the protection of our
environment. Contact local authorities for information on
your local recycling facility.
11
Publicité
