I-VALO VEGA W Série Notice D'utilisation, D'installation Et De Maintenance page 16

Operation and maintenance instructions
I-VALO VEGA
These instructions do not claim to cover all details or variations of luminaries or
accessories, or to provide for every possible contingency to be met in connection with
installation, operation or maintenance. The operation and maintenance instructions
can be found also on our website at www.i-valo.com or may be requested from your
salesperson.
1. INSTALLATION
• The luminaire may be installed only by a qualified electrician, in
accordance with local legislation.
• The operating voltage should be 230V ±3%. Temporarily, a maximum
fluctuation of ±5% is allowed. Sudden changes of over ±10% in mains
voltage may lead to inoperative lamps.
• All I-Valo luminaires are always supplied with either a complete
mounting rail or with installation holes drilled in the frame. No other
holes may be made in the frame.
• The condition of the mounting rail and bracket should be checked in
conjunction with bulb replacement.
2. OPERATION
• The luminaire may be used only in the environment for which it is
intended in accordance with the rating label.
• The luminaire must not be operated with a broken cover part.
• If the front glass or pc/acrylic cover gets broken, it must be
replaced immediately.
3. MAINTENANCE
• Disconnect the luminaire from the power supply before any
maintenance operation.
• Wait 60 seconds until the capacitors are fully discharged.
• The luminaire components will take several minutes to cool.
4. CLEANING
• The external surfaces of the luminaire should be regularly cleaned of
dirt, thus ensuring effective operation. A thick layer of dust on top
of the luminaire increases its internal temperature and shortens the
service life of the electrical components.
• I-VALO VEGA luminaires are sealed and pressure-tested, and they are
equipped with highly efficient equalisation air filtering. This means
that it is not usually necessary to clean the inside of the luminaire. If,
however, you decide to clean the inside of the luminaire do not use any
abrasive agents, in order to avoid scratching the reflector.
• If necessary, clean the outside surface of the luminaire with neutral
detergents, e.g. dish washing agent. These are also suitable for
cleaning the glass and polycarbonate parts of the luminaires.
• It is absolutely prohibited to use a high-pressure washer for
cleaning the luminaires. Pressurized water can easily damage the
luminaire, especially an uncovered filter.
• Check the sealings when changing the lamp and clean them if
necessary.
• Make sure that the cover parts are properly in place and that all latches
are closed tightly.
16
60 sec!
5. ChANGING ThE FILTER
• In normal industrial surroundings the condition of filters should be
checked every time the lamps are changed. It is recommendable to
replace the filter concurrently with every second lamp change, or
more often if the conditions require.
• In I-VALO luminaires, a number of filter types are used. Choose the
filter type in accordance with the luminaire's end use.
GORETEX-filter Dust filter
6. LAMP REPLACEMENT
• Any defective bulb must immediately be replaced with a new one.
• Verify the appropriate bulb type from the luminaire's rating label. The
bulb type stated in the label and the connecting device must match
each other.
• Familiarize yourself with the user guide that comes with the lamp.
• Follow the lamp manufacturer's instructions for burning hours and
economical service lifetime. "Group relamping" of luminaries is
recommended.
• E40 lamp holders are equipped with a safety spring, twist the new
lamp firmly into the lamp holder.
• Any luminaire that does not have a bulb inside must be disconnected
from the power outlet!
7. ChANGING ELECTRICAL COMPONENTS
• If a luminaire component breaks for any reason, it must immediately
be replaced with a similar component.
• The rating plate indicates the electrical values and appropriate light
source for the luminaire.
• Remember to check the condition of the electrical components and
wiring in conjunction with every bulb replacement; at the same time,
you should also replace any other wearing parts of the luminaire.
• The indicative service life of the components is as follows: igniter
40,000 hrs, capacitors 40,000 hrs, ballast 50,000 hrs
• We recommend use of the I-VALO SERVICE PACK spare parts. This will
ensure that you have the correct components in your luminaire and
secure energy-efficient and faultless operation of the luminaire in the
future. For more information about spare parts packs, please contact
your local reseller.
• Do not change electrical connections or the location of the
components!
ENGLISH
Double-effect filter