Dremel 8200 Traduction De La Notice Originale page 21

ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools into household
waste!
A ccording the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools
that are no longer usable must be collected
separately and disposed of in an environmentally
correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . 10,8 V
Amperage Rating . . . . . . 1,3 – 2,0 Ah
Rated Speed . . . . . . . . . . n 33000 min
Collet Capacity . . . . . . . . 0,8 mm, 1,6 mm, 2,4 mm,
SPECIFICATIONS CHARGER
Input. . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . 3,6 V - 10,8 V , 1,5 A
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING
THE TOOL.
BATTERY CHARGE CONDITION INDICATOR LIGHTS
Your tool is equipped with charge condition indicator
lights )picture 1 D(. The indicator lights shows the charge
condition of the battery.
3 of 3 Solid LED's = 67-100%
2 of 3 Solid LED's = 34-66%
1 of 3 Solid LED's = 16-33%
1 of 3 Flashing LED's = 0-15%
3 "side to side" lights – battery charge is too low to run
tool. Recharge the battery.
3 "flashing" lights – battery is too hot for use. Turn tool off
and let battery cool down.
Your tool is equipped with advanced electronics that
protect the Li-Ion cells in the battery from damage due to
excessive operating temperature and/or current draw. If
the warning symbol illuminates red and/or the tool stops
working during heavy use, this most likely indicates that the
Li-Ion cells are near their maximum operating temperature,
and the battery pack should either be changed or allowed
to cool to ambient temperature before continuing use. If the
tool automatically turns off due to overload conditions, the
-1
3,2 mm
switch must be turned off for a few seconds to allow the
circuit to reset before continuing use.
IMPORTANT CHARGING NOTES
1. The charger was designed to fast charge the battery
only when the battery temperature is between 32°F
)0°C( and 113°F )45°C(. If the battery pack is too hot
or too cold, the charger will not fast charge the battery.
)This may happen if the battery pack is hot from
heavy use(. When the battery temperature returns to
between 32°F )0°C( and 113°F )45°C(, the charger will
automatically begin charging.
2. A substantial drop in operating time per charge may
mean that the battery pack is nearing the end of its life
and should be replaced.
3. Remember to unplug charger during storage period.
NOTE: Use of chargers or battery packs not sold by
Dremel will void the warranty.
CHARGING BATTERY PACK (MODEL 875)
Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger's green indicator
light will go ON. This indicates the charger is receiving
power and the charger is ready for operation.
When you insert the battery pack into the charger, the
charger's green indicator light will begin to "BLINK". This
indicates that the battery is receiving a fast charge.
PICTURE 10
A. Battery pack
B. Charger
C. Green light
When the indicator light stops "BLINKING" )and becomes
a steady green light( fast charging is complete. The
battery pack is fully charged and can be removed from the
charger.
When you begin the charging process of the battery pack,
a steady green light could also mean the battery pack is
too hot or too cold.
Fast charging is only possible when the temperature range
of the battery pack is between 0°C and 45°C.
When needed, the internal fan of the charger will turn on to
aid the charging process and speed.
As soon as the battery pack reaches the correct
temperature range, the battery charger will automatically
switch to fast charging.
The battery pack may be used even though the light may
still be blinking. The light may require more time to stop
blinking depending on temperature.
The purpose of the green light is to indicate that the
battery pack is fast-charging. It does not indicate the exact
point of full charge. The light will stop blinking in less time
if the battery pack was not completely discharged.
If the green indicator light is "ON", the battery pack cannot
accept a charge.
The Dremel multitool is a high quality precision tool that
can be used to perform detailed and intricate tasks. The
wide range of Dremel accessories and attachments allow
you to perform a large variety of tasks. These include tasks
such as sanding, carving, engraving, routing, cleaning and
polishing.
PICTURE 1
A. Shaft lock button
B. On/Off switch
C. Hanger
21
GENERAL