Publicité
Les langues disponibles
Les langues disponibles
SET UP (cont.)
CONVERGE (cont.)
Note:
After selecting, press VOL
DEFAULT feature. When using this feature in Zoom
mode, the effect can only be verified when you exit all
menus and display normal picture.
CONVERGE.
PRESS ACTION TO RETURN
CONVERGENCE ADJ.
Procedure
•
After pressing VOL
will be displayed.
•
Then use the navigation buttons on the remote control
to align the horizontal and vertical green lines on screen,
with the cabinet reference marks on top center and left
center of cabinet, as shown below.
Reference Marks
ALIGN GREEN LINES TO THE
CENTER MARK ON THE CABINET
Front of cabinet
PRESS ACTION TO CONTINUE
ACTION
•
Press
to display red center correction screen.
•
Use the navigation buttons on the remote control to align
the red cross with the white cross pattern at the center of
the screen.
Note:
To prevent picture tube damage, do not leave
test pattern on for an extended period of time.
•
Then press "0" on the remote control keypad to display
the BLUE center correction screen, repeat procedure for
adjusting blue. If needed press "0" again to return to
RED correction screen.
Note:
An adjusted cross pattern appears white with a minimum
of color protrusion.
IF RED IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT
UP
LEFT
RIGHT
DOWN
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO CONTINUE
to activate RESET TO
SET UP
CONVERGENCE ADJ.
RESET TO DEFAULT
the align Green to Center screen
PRESS CH AND VOL KEY TO
UP
RIGHT
LEFT
DOWN
IF BLUE IS PROTRUDING FROM
CENTER CROSS, PRESS CH AND
VOL KEY TO CORRECT
Press
UP
"0"
LEFT
DOWN
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO CONTINUE
NINE POINT CONVERGENCE CORRECTION
Note:
Remote Control must be in TV mode.
Procedure
ACTION
•
Press
•
Press the 1 through 9 keypad buttons on the remote
control to select the desired convergence position.
•
Use the navigation buttons to align the RED cross with
the white cross pattern.
Note:
An adjusted cross pattern appears white with a minimum
of color protrusion.
•
Press "0" on the remote control keypad to display the
BLUE correction screen, then repeat procedure.
2
1
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
4
CORRECTING RED
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO EXIT
PRESS ACTION TO EXIT
8
7
•
To exit press
OTHER ADJ.
Highlight OTHER ADJ. and press VOL
menu field.
Note:
While sub sub-menu features are highlighted, press
VOL
to adjust or activate.
•
MODE - To select TV (antenna) or CABLE mode
depending on the signal source.
•
AUTO PROGRAM - To automatically program all
channels received through the RF input.
•
MANUAL PROGRAM - To manually add or delete
RIGHT
channels.
•
AUTO POWER ON - Select SET to power up the TV at
the same time as the Cable box or other components or
select OFF.
•
CHAN BANNER - Select ON to display onscreen banner
when changing channels.
•
IMAGE SHIFT - Selecting ON is recommended for this
feature to prevent image retention on screen.
I
M
CON
ENUS
to display red correction screen.
2
3
1
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
4
6
CORRECTING RED
PRESS 0 TO ADJUST BLUE
PRESS ACTION TO EXIT
PRESS ACTION TO EXIT
9
8
7
3
1
PRESS # KEY TO SELECT POS.
PRESS CH AND VOL KEY TO CORR.
Press
6
4
"0"
CORRECTING BLUE
PRESS 0 TO ADJUST RED
PRESS ACTION TO EXIT
PRESS ACTION TO EXIT
9
7
ACTION
repeatedly, then press CH
to enter sub sub-
SET UP
CABLE
MODE
AUTO PROGRAM
MANUAL PROGRAM
OFF
AUTO POWER ON
.
ON
OTHER ADJ
CHAN BANNER
ON
IMAGE SHIFT
PRESS ACTION TO RETURN
O
PERATION
2
3
6
9
8
.
29
Publicité
