Publicité
User Manual
Introduction
Thank you for purchasing the LINDY Fibre Optic DVI-D Extender!
This Fibre Optic Extender allows you to transmit DVI-D Single Link signals up to maximum
resolutions of 1920x1200 and Full HD 1080p up to a distance of 500m/1600 feet using a single
standard multimode 50/125µm LC Duplex fibre cable. For long distances of up to 1500m/5000
feet a single standard monomode 9/125µm LC Duplex fibre cable must be used.
Features
•
Extends DVI-D or DVI HDTV / HDMI signals up to 1500m/ 5000 feet
•
Suitable for use with Computer, Video Wall and Home Theater equipment
•
Uses a single standard LC Duplex fibre cable (not included)
•
Auto power save mode
•
Preset EDID data set and Self-EDID learning feature
•
Auto Laser disable if fibre cable is broken or removed
Specification
•
Total Bandwidth 6Gbit/s. over a single 2-core fibre Optic Cable
•
Compatible with DVI 2.0 specification
•
HDCP and HDTV compatible
•
Supports DVI-D Single Link
•
Supports resolutions up to 1920x1200@60Hz and FullHD1080p/60
•
Supports HDMI / HDTV / HDMI audio signals over DVI connectors
•
Dimensions: 4cm x 7cm x 1.5cm (WxDxH), each unit (without LC cable)
•
Multi country power supply 100...240VAC / 5VDC ~1A
Package Contents
LINDY Fibre Optic DVI-D Extender x 2 (1x Transmitter, 1x Receiver)
Multi-Country Power Adapter (5VDC) x 2
This User Manual
Do NOT introduce strain or stress to the fibre optic LC cable and connectors!
Do NOT bend the fibre cable below the minimum allowed radius, approximately 5cm -
see supplier's specification!
English
1
User Manual
Pre-Installation Remarks
Important! Before starting the installation, please ensure that all devices are powered off.
The EDID preset timings stored in the extender are the following:
720x400@70Hz; 640x480@60/72/75Hz; 800x600@60/72/75Hz; 1024x768@60/70/75Hz;
1152x870@60HZ; 1280x960@60Hz; 1152x864@75Hz; 1280x720@60Hz;
1280x1024@60/75Hz; 1440x900@60Hz; 1600x1200@60Hz; 1680x1050@60Hz;
1920x1080@60Hz; 1920x1200@60Hz
If the resolution of your monitor is not included above, you must use the Self-EDID learning
feature of the transmitter unit to copy the EDID data from the monitor into the transmitter unit.
Self-EDID learning procedure
1. Power on the display.
2. Plug the 5VDC power adapter into the transmitter unit.
3. Connect the transmitter unit to the display/sink, not to the HDMI source.
4. Push the Self-EDID button with a narrow pin. The R/W LED will blink three times to
indicate the reading of EDID information. When the LED is totally turned off, the EDID
copying procedure is done.
Insert a narrow pin into this
hole to push the Self-EDID
button
Recovery of original EDID setting
Plug 5VDC power adapter into the transmitter and disconnect all other connectors.
Push the self-EDID button with a narrow pin. The R/W LED will blink six times to indicate the
recovery of EDID information. When the LED is totally turned off, the recovery procedure
is done.
The Extender will get very hot during operation!
Avoid touching it directly and install it with adequate ventilation!
When copying the EDID
information this LED will be
blinking 3 times
CAUTION!
2
English
Publicité
