About This Documentation; Documentation Validity; Related Documents; Presentation Of Information - Emerson AVENTICS ST6 Notice D'instruction

1 About This Documentation

1.1 Documentation validity

These instructions contain important information on the safe and appropriate in-
stallation and operation of the sensor.

1.2 Related documents

The sensor is a system component.
Also observe the system documentation from the system manufacturer.
u

1.3 Presentation of information

1.3.1 Notes on safety

In this document, there are safety instructions before the steps whenever there is
a danger of personal injury or damage to the equipment. The measures described
to avoid these hazards must be followed.
Safety instructions are set out as follows:
Hazard type and source
Consequences
• Precautions
Warning signs and signal words have the following meanings:
Hazard classes according to ANSI Z 535.6-2006
Indicates a dangerous situation which, if not avoided, could result in death or
serious injury.
Indicates a dangerous situation which, if not avoided, could result in minor or
moderate injury.

1.3.2 Symbols

If this information is disregarded, the product cannot be used or oper-
ated optimally.
2 Notes on safety

2.1 About this chapter

The product has been manufactured according to the accepted rules of safety
and current technology. Even so, there is a risk of injury or damage if the follow-
ing general safety instructions and the specific warnings given before the steps in
this documentation are not observed.
1. Read these instructions completely before working with the sensor.
2. Keep these instructions in a location where they are accessible to all users at
all times.
3. Always include the operating instructions when you pass the sensor on to
third parties.

2.2 Intended use

1. The sensor is only intended for industrial applications.
2. Use within the limits listed in the technical data.
3. The sensor is to be used to detect magnetic fields in explosive areas.

2.3 Improper use

It is considered improper use if the sensor
• is used for any application not stated in these instructions, or
• is used under operating conditions that deviate from those described in these
instructions.
AVENTICS TM ST6 | R412027659-BAL-001-AB | English
SIGNAL WORD
WARNING
CAUTION

2.4 Personnel qualifications

Assembly and commissioning require basic electrical and pneumatic knowledge.
Assembly and commissioning may therefore only be carried out by qualified elec-
trical or pneumatic personnel or an instructed person under the direction and su-
pervision of qualified personnel. Qualified personnel are those who can recognize
possible hazards and institute the appropriate safety measures, due to their pro-
fessional training, knowledge, and experience, as well as their understanding of
the relevant regulations pertaining to the work to be done. Qualified personnel
must observe the rules relevant to the subject area and have qualifications ac-
cording to the Technical Rules for Operational Safety (TRBS 1203).

2.5 General safety instructions

1. Observe the regulations for accident prevention and environmental protec-
tion for the country where the device is used and at the workplace.
2. Do not modify or convert the device.
3. Only use the device within the performance range provided in the technical
data.
4. The warranty will not apply if the product is incorrectly assembled.
5. Do not place any improper mechanical loads on the product under any cir-
cumstances.

2.6 Safety instructions related to the product and technology

2.6.1 During assembly

Make sure the relevant system component is not under pressure or voltage
u
before assembling the product or when connecting and disconnecting plugs.

2.6.2 During operation

1. Only commission the sensor after it has been completely assembled, as well
as correctly connected and tested.
2. Observe the operating conditions and data printed on the relevant sensor or
stated on its rating plate.
3. Do not disconnect plugs or lines when the sensor is under voltage.
2.7 ATEX – information on explosion protection
The sensors are certified and labeled according to the enclosed declaration of
conformity.
They can be used
• with gases, mists, or vapors in zone 2
• with flammable dust particles in zone 22

2.7.1 Explanations concerning identification

Year of manufacture of the sensor: The first two digits in the 5-digit
date code on the rating plate indicate the year and the last two digits
indicate the week.
II 3G Ex ec IIC T4 Gc X
II 3D Ex tc IIIC T135°C Dc X
Due to the small size of the sensor, the ATEX identification is located on a cable
flag.
Danger of an ignition source due to impermissible operating conditions, con-
nections, and parameters!
Operating the sensor under impermissible operating conditions can result in
an explosion.
1. Observe the permissible operating conditions, in particular the ambient
temperature and the mechanical protection for the device.
2. The ATEX sensor is only intended for complete installation in suitable T-
slots.
3. Note the limited temperature range for ATEX conditions.
4. Do not disconnect the connecting cable from the sensor if it is under volt-
age.
5. Observe the relevant Ex guidelines for installation, maintenance, and re-
pair, especially EN 60079-14.
WARNING
7