Publicité
Les langues disponibles
Les langues disponibles
Fabric protection
D
soleplate cover
(Model dependent)
The fabric-protection soleplate cover (19*) is
used for steam-ironing delicate garments at
maximum temperature without damaging them.
Use of the soleplate cover also does away with
the need for a cloth to prevent shine on dark
materials.
It is advisable to first iron a small section on the
inside of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place
the tip of the iron into the end of the soleplate
cover and pull the elastic strap over the lower
rear of the iron until it fits tightly. To release the
soleplate cover, pull the elastic strap and remove
the iron.
The fabric-protection soleplate cover may be
purchased from our customer service or from
our website
Accessory code
(After-sales)
00571510
E
calc'nClean Plus
Cleaning the Boiler
To extend the life of your steam generator and to
prevent any build up of scale, it is essential that
you rinse out the filter (4*) and the boiler after
several hours of use. If the water is hard,
increase the frequency.
Do not use descaling agents for rinsing out the
boiler, as they could damage it.
Automatic clean warning
Pilot light (11) will flash indicating that boiler must
be rinsed (three beeps may be heard).
1. Check carefully that the appliance is cold and
unplugged for more than 2 hours, and that the
water tank (1) is empty.
2. Fix the iron to the stand by inserting the tip of
the iron into the front slot and moving the
fixation lever (13) against the heel of the iron.
3. Place your appliance over a sink or bucket.
4. Lean the appliance on the opposite side of the
filter opening.
5. Unscrew the filter (4*) and take it out.
6. (model dependent)
To wash the scale collector, place it under the
water tap and wash it up until calc residues are
removed. Squeeze it as indicated in the picture
a).
18
S I E ME NS
Name of accessory
(Online shop)
TZ20450
To obtain the best result, you may immerse the
scale collector for approximately 30 minutes in
tap water (250 ml) mixed with a measure (25
ml) of descaling fluid, as indicated in the
picture b). Then, rinse it again with water (very
important!).
The descaling fluid can be obtained from our
After-sales service or from our website.
Accessory code
(After-sales)
00311715
7. Holding your steam generator in the lateral
position and using a jug, fill the boiler with 1/4
litre of water and replace the filter.
8. Shake the base unit for a few moments,
unscrew the filter again and empty the boiler
completely over a sink or bucket.
For best results, we recommend that this
operation is performed twice.
Important: before re-closing, make sure no
water remains in the boiler.
9. Replace and tighten up the filter.
To reset the "calc'nClean" counter, switch
the steam station off twice, keeping it off for
at least 30 seconds each time.
(on → 30s off → on → 30s off → on)
Cleaning &
Maintenance
Attention! Risk of burns!
Always unplug the appliance from the mains
supply before carrying out any cleaning or
maintenance operation on it.
1. After ironing, pull out the plug and allow the
appliance to cool down before cleaning.
2. Wipe the housing, handle and iron body with a
damp cotton cloth.
3. If the soleplate is soiled with dirt or scale,
clean it with a damp cotton cloth.
4. If the cloth is synthetic, it may melt due to the
high temperature on the soleplate (19). Switch
off the steam and rub off any residue
immediately with a thickly folded, dry cotton
cloth.
5. Never use abrasive products or solvents. To
keep the soleplate (19) smooth, you should
avoid hard contact with metal objects. Never
use a scouring pad, or chemicals to clean the
soleplate.
Name of accessory
(Online shop)
TDZ1101
Publicité
