i-tec U3DVIDOCKL Mode D'emploi page 5

Quick Start / USB 3.0 Docking Station
INTRODUCTION
Thank you for purchasing the i-tec docking station that will allow you to connect your favorite pieces of
hardware such as a keyboard, mouse, external disk or USB printer through the USB ports, audio system
through the input for earphones and microphone, internet modem / LAN Ethernet PC network through the
LAN port, monitor through the DVI-I port, etc. to your notebook / tablet / PC. You can connect all of these
pieces of hardware easily and fast to your notebook / tablet / PC by a single USB 3.0 cable. You can display
your data on modern LCD and plasma monitors and TV sets because the docking station is equipped with
a DVI-I port. The graphic chip which makes the "heart" of the docking station supports even the Full HD+
resolution (2048 x 1152 pixels).
CONTENT OF THE PACKAGE
• i-tec USB 3.0 docking station with a stand
• Power adapter
• USB 3.0 cable (one end connector type A, the second end type B; 100 cm) – for connecting to a notebook
/ tablet / PC
• Quick Start
SYSTEM REQUIREMENTS
Hardware requirements: notebook / tablet with OS Win 8 / Win 10 PC with a free port USB 3.0 / 2.0. If you
have USB 2.0, the data transfer speed will be reduced. Processor Intel Pentium 1.2 GHz and higher, 512 MB
RAM.
Operating system: Windows 7 / 8 / 8.1 / 10 32/64 bit, macOS X, Linux Ubuntu, Android 5 (Lollipop) and later,
Chrome OS.
For playing a DVD on an additional monitor the processor shall be at least Intel Pentium 2.0 and higher, 1 GB
RAM and a screen resolution shall be 800x600 and 16 colors.
CAUTION!
Before the installation on the USB 3.0 port make sure that you have the most recent drivers installed for
this port (for the USB 3.0 controller into notebook / tablet / PC). Products with the USB 3.0 SuperSpeed
technology have been used since 2010; however, the drivers for the supported equipment are still
undergoing some fine tuning. Your notebook / tablet / PC needs to be equipped with the USB 3.0 interface
so that you can utilize the advantages of the fast USB 3.0 equipment. Its problem free function is ensured
by the chipset which needs to have the current drivers available.
Problems that you can encounter during the installation or use of our USB 3.0 equipment are very often
caused by the installed outdated drivers for the USB 3.0 controller or chipset of your notebook / tablet /
PC. Other problems can be caused by outdated firmware of the USB 3.0 port controller. Most frequently it is
one of the following manufacturers: Intel, Renesas (former NEC), Via (VLI), AS Media, Fresco Logic, Etron.
You can find the most recent drivers for the i-tec products on our website www.i-tec.cz/en in the „Download"
tab for the individual products. The „Problems with USB 3.0" tab includes a more detailed description with
links to the drivers and firmware for USB 3.0 controllers.
After Windows 10 has finished installing, run Windows Update. (Start button > Settings > Update). This is
critical, as your system may be missing various drivers after installation. After running Windows Update and
rebooting, run Windows Update again. Repeat this process until there are no new updates found.
Note:
• The installation of audio ports, reader and the USB HUB (for USB 3.0 / 2.0 ports type A) is automatic from
the system, the other ports need to be installed.
• Before the first connection of the docking station to a notebook / tablet / PC it is necessary first to install
the LAN and DVI-I port and only then to connect the equipment to the docking station.
INSTALLATION OF DRIVERS IN WINDOWS 7 / 8 / 8.1 / 10 (32/64 BIT VERSION)
Before the first use do not connect the docking station to the notebook / tablet / PC, until you install the
corresponding drivers for the LAN and DVI-I port from the www.i-tec.cz/en. The equipment drivers need to
be installed only before the first use.
EN
5