Start Operating Setup - Whirlpool W10918732B Instructions D'installation

Start Operating Setup

Before proceeding, it is worth noting that, despite all of the
options available, an owner can simply choose to uncrate a
new commercial washer, hook it up, plug it in, and have a washer
that operates.
Washers are preset at the factory for an 11-minute wash period
and 3 rinses (no extra rinse).
SET-UP CODES
The WARM button will advance you from code to code.
■
The HOT button will change the code value.
■
The COLD button will select or deselect options.
■
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two
or three right-hand characters.
NOTE: The first line of each code indicates the factory default
for 9150 models.
CODE
REGULAR CYCLE PRICE (Factory Default)
6. 08
6. 08 When the d.xx is set to d.00, this 6.xx value
represents the number of coins needed to start the
washer; may adjust from 0–39. Change this value
by pressing the HOT button. 6.08 = 8 coins. 9160
models default to 6.00.
6. 01 When the d.xx is set to d. CS, this 6.xx value
represents the number of push-in actuations of the
coin slide to start the washer. 6.01 would equal one
coin slide activation.
g Press the WARM button once to advance
to next code.
7. 11 WASH LENGTH
7. 11 This is the number of minutes for WASH. Washer
comes from the factory preset with 11 minutes.
Choose from 9–17 minutes by pressing the HOT
button.
g
Press the WARM button once to advance
to next code.
ADDITIONAL RINSE OPTION
8. 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
00 Not Selected 'OFF'.
8.
8. Ar Selected 'ON'.
Press the COLD button once for this selection.
Press the WARM button once to advance
g
to next code.
CYCLE COUNTER OPTION
9. 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
9. 00 Not Selected 'OFF'.
9. 0C Selected 'ON' and not able to be deselected.
Press the COLD button 3 consecutive times to select
'ON'. Once selected 'ON,' it cannot be deselected.
Press the WARM button once to advance
g
to next code.
MONEY COUNTER OPTION
1. 00
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
EXPLANATION
CODE
1. 00 Not Selected 'OFF'.
1. 0C Selected 'ON'.
Press the COLD button three consecutive times
to select 'ON' and three consecutive times to remove
(Not Selected 'OFF'). Counter resets by going
from 'OFF' to 'ON'.
1. C0 Selected 'ON' and not able to be deselected.
To select 'ON' and not able to be deselected,
first select 'ON', then within two seconds, press
the COLD button twice, HOT once, and exit
the set-up mode.
Press the WARM button once to advance
g
to next code.
2. 00 SPECIAL PRICING OPTIONS
This option is either SELECTED 'ON' or NOT
SELECTED 'OFF'.
2. 00 Not Selected 'OFF'.
2. SP Selected 'ON'. Press the COLD button once for this
selection.
If SPECIAL PRICING OPTION is selected, there
is access to codes '3.' thru '9.'
g Press the WARM button once to advance
to next code.
OPTIONS TO USE IF SPECIAL PRICING
IS SELECTED:
3. 08 SPECIAL CYCLE PRICE
3. 08 Represents the number of quarters (coin 1) needed
to start the washer; may adjust from 0–39. (See b.xx
setup for VALUE OF COIN 1.) Advance from 0–39 by
pressing HOT. Factory default of 8 quarters = $2.00.
3. 00 Model 9160: Factory default of 0 quarters.
g Press the WARM button once to advance
to next code.
5. 00 TIME-OF-DAY CLOCK, MINUTES
5. 00 This is the TIME-OF-DAY CLOCK, minute setting;
select 0–59 minutes by pressing the HOT button.
Press the WARM button once to advance
g
to next code.
TIME-OF-DAY CLOCK, HOURS
6. 00
NOTE: Uses military time – 24 hr. clock.
6. 00 This is the TIME-OF-DAY CLOCK, hour setting;
select 0–23 hours by pressing the HOT button.
Press the WARM button once to advance
g
to next code.
SPECIAL PRICE START HOUR
7. 00
NOTE: Uses military time – 24 hr. clock.
7. 00 This is the start hour; select 0–23 hours. Select
START HOUR by pressing the HOT button.
Press the WARM button once to advance
g
to next code.
SPECIAL PRICE STOP HOUR
8. 00
NOTE: Uses military time – 24 hr. clock.
8. 00 This is the stop hour; select 0–23 hours. Select STOP
HOUR by pressing the HOT button.
Press the WARM button once to advance
g
to next code.
EXPLANATION
11