Hudora 72175/00 Instructions De Montage Et Mode D'emploi page 3

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral component of
the product. Therefore, please store them and the packaging carefully in case que-
stions arise in the future. Please always include these instructions when handing on
the product to a third party. This product must be assembled by an adult. This product
is designed for private/domestic use only. This product is not designed for commer-
cial/industrial use. The use of the product requires certain capabilities and skills. Al-
ways adjust according to the age of the user and use for the purpose it has been de-
signed for.
TECHNICAL SPECIFICATIONS
Item: Rubber board swing
Item number: 72175/00
Max. Height for Suspension: 250 cm
Min. Height for Suspension: 160 cm
Max. Body Weight: 100 kg
Dimension: 45 x 17,5 cm
Purpose: Device powered by muscle power, for swinging in a
sitting position.
Minimum user age: 3 years
If you have assembly problems or would like further information on the product, we
have all you need and more at http://www.hudora.de/.
CONTENTS
1 x Swing seat | 2 x Swing ropes | 2 x Metal brackets for swing seat | 1 x These in-
structions
Other parts which may be included with the delivery in some circumstances are not
required.
SAFETY INSTRUCTIONS
• WARNING! Only for domestic use. Only suitable in the outdoors area.
• WARNING! Only use under direct supervision of an adult!
• WARNING! Not suitable for children under 36 months. Risk of falling.
• WARNING! Not suitable for children under 36 months. Long cord. Strangulation ha-
zard.
• WARNING! Not suitable for children under 36 months. Small parts. Choking hazard.
• The owners of the swing as well as the competent supervisory personnel are
responsible for ensuring that all users follow the instructions in the operation
manual.
• Do not make any technical modifications.
• Changes to the original product must only be carried out according to manufacturer
specifications.
• No one is permitted to gain access to the swing area during use.
• Never stand or kneel on the swing.
• Always hold yourself firmly with both hands.
• No objects of any kind must be in the vicinity of the swing zone (trees, walls, fences,
clotheslines).
• Make sure that you have a safety clearance of at least 2 m (front and back) beyond
the maximum reach of the swing and make sure the ground is level and shock
absorbing (e.g. grass) without any sharp edges or pointed objects, obstacles, in-
clines, levels, steps or hard surfaces (e.g. concrete) etc.
• Clearance to stationary components on the side, such as the swing scaffolding,
must be at least 40 cm.
• Maximum raised height must not exceed 250 cm as measured from the ground.
• Swinging components, such as a neighboring swing, must be placed at a distance
of at least 60 cm.
• In idle mode, the swing must be at least 40 cm and maximally 60 cm from the
ground.
• You should never install a swing in such a way that the user could be blinded by sun
rays.
• Suspension connectors shall be of a design that will prevent unintentional discon-
nection.
• When permanently irradiated with UV light, the material ages significantly faster. To
avoid premature aging and thereby extend the service life, you should always store
the product in a dry and dark place when not in use. Do not permanently expose the
product to wind, moisture, extreme temperatures or sunlight.
All images are examples of the design.
ASSEMBLY OF THE BRACKETS
Prior to installation, carefully select and check the
location where you will install the swing. Please
make sure that the swing carrier is adequately sta-
ble. Please also take into account that swinging pro-
duces centrifugal forces that can put a lot of strain
on the swing carrier. Please consult an expert (sta-
tics expert, architect, carpenter) and ask how much
load your swing carrier can tolerate.
Mount the metal brackets on both sides of the rubberized swing board from above as
shown in Fig. 1. Make sure the screws are tight. It should only be possible to move the
brackets slightly.
HANGING DEVICE AND ADJUSTMENT
The hanging points must be at least as far apart as the swing seat + 100mm. The
swing is packaged with two ropes and adjustment eyelets, so that the height of the
swing can be variably aligned with any suitable hanging device. Before hanging up the
swing, insert the end of the rope through the bracket using the eyelet (rear hook) (B)
of one of the ropes. (Fig. 2) Then lay the rope double for about half its length (approx.
20 cm) and guide the resulting loop from behind through the open adjustment eyelet
(B). (Fig. 3) Close the adjustment loop through the loop so that the rope cannot be
pulled out (Fig. 4). Repeat this process with the second rope and eyelet of the swing.
The hanging swing can now be individually adjusted. No one should sit on the swing
while making the adjustments. When extending or reducing the length of the swing
ropes please make sure that the ropes remain equally long at all times. If the lengths
of the ropes differ, this will lead to circular pendulum movements of the swing. Make
sure that swing is set up in such a way that the person using the swing cannot reach
the ground with the tips of his or her toes. If in doubt, perform a few gentle test
swings.
MAINTENANCE AND STORAGE
Check the product for damage or traces of wear and tear before and after each use.
We also recommend before each use:
• to check for the firm sitting of nuts and bolts, tighten if necessary
• to lubricate moving parts in order to minimize wear
• to check all covers of screws and sharp edges and replace if necessary
• to replace defective parts according to the manufacturer's instructions
• to check swing seats, chains, ropes and other means of attachments for evidence
of deterioration
You should also replace all the plastic parts after a maximum of 5 years to prevent a
possible failure of these parts.
Use only a dry or damp cloth to clean the product; do not use special cleaning agents!
Check the product for damage or traces of wear and tear before and after each use.
Do not make any structural changes. For your own safety, please use original spare
parts only. These can be sourced from HUDORA. If parts become damaged or if sharp
edges or corners should develop, the product may not be used any more. If in any
doubt, please contact our service team (http://www.hudora.de/service/). Store the
product in a safe place where it is protected from the elements, cannot be damaged,
and cannot injure anyone.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection point
in your area. Local waste management companies will be able to answer your que-
stions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we put
just as much effort into rectifying them. Therefore, you can find numerous information
on the product, replacement parts, solutions to problems and lost assembly manuals
at http://www.hudora.de/service.
3/8