Important; General Characteristics - Astralpool 35933 Manuel D'installation

ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Mini light for swimming pool, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
Concrete pool floodlamp, 35933 / 36656
Housing body
Floodlamp unit
Bag of screws
Prefabricated pool floodlamp, 35934 / 36658
Housing body
Floodlamp unit
2 watertight joints
Bag of screws

2. GENERAL CHARACTERISTICS:

This floodlamp has been designed to be used fully submerged underwater in fresh water. It is a Class III electric apparatus
with very low safety voltage (12 V with alternating current).
The floodlamp complies with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a
nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components
which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
In order to clearly light a pool it is recommended to install a floodlamp every 5 m
which are especially deep, a floodlamp is required for every 10 m
In order to prevent glare, the floodlamps should be installed so that they face away from the residence or usual view of the
swimming pool.
In the event that lighting is used in training or competition pools, the floodlamps should be installed on the sides to
prevent glare on the swimmers.
To avoid emptying the pool if the projector has to be handled, it is recommended to install it in places which are accessible
from the upper edge of the pool.
Prior to installation verify that the gland seal has been fully tightened.
The floodlamp should be placed on the wall of the pool at approximately 400-700 mm from the water surface (Fig. 1). The
crosshead and the clamp must be placed so that that the word "TOP" is located on the upper part
The method of fastening the crosshead mount to the pool wall varies depending on whether it is a floodlamp for concrete
pools or prefabricated pools.
Concrete swimming pool (Model 35933 / 36656)
To install a floodlamp in a concrete pool the housing (nº11) should be fixed in the wall of the swimming pool (Fig.1). Use
eight M6x24 (nº21) screws to secure the housing clamp to the pool.
Prefabricated swimming pool (Model 35934 / 36658)
To install a floodlamp in prefabricated swimming pool make a circular hole with a diameter of 110 mm (Fig. 2).
Install the housing and one of the joints on the outer side of the pool. Install the other joint (no. 3) on the inner side and to
secure the three components (Fig. 3). Make sure that the cable outlet of the housing remains on the upper part.
Use eight 6 x 24 screws (no. 21) to secure the clamp to the wall of the pool. (Fig 5). Make sure that the word "TOP" is
located on the upper part.
Panelled swimming pool with Liner (Model 35935 / 36660)
The projector can be installed in a metal sheet or plastic panelled swimming pool, using the template, and making a circular
hole of 147 mm. diameter and 4 holes
Place the recess (no. 11) through the inside of the pool and bolt the 4 DIN 7982 4.8x25 screws (no. 22) (Fig. 6). Make sure
that the cable outlet from the recess is on the upper side.
Stick the adhesive joint (no. 3) on the inside of the pool and then place the liner.
Panelled pool with Liner floodlamp, 35935 / 36660
3
of water volume.
4 mm (Fig. 2).
2
Housing body
Floodlamp unit
2 watertight joints
Bag of screws
2
of water surface. In swimming pools