Witter C34AU Instructions De Montage

MATERIALS
A 1 Cross Bar with European facing to 94/20/EC A50-1
B 1 RHS Plate
D 1 LHS Plate
E 1 RH Support Bracket
F 1 LH Support Bracket
G 1 Spacer Plate
ZEQ2 1 Electrical Bracket
ZEP1 1 Electrical Plate
H 1 M10x25x1.5 Bolt, Nut, Lock Washer and Washer (20 mm OD)
J 6 M10x40x1.5 Bolt, Lock Washer and Washer (30 mm OD)
L 2 M16x50x2.00 Bolt, Nut and Lock Washer
M 2 M12x35x1.75 Bolt, Lock Washer and Washer (30 mm OD)
N 2 M12x45x1.75 Bolt, Nut, Lock Washer and Washer (30 mm OD)
P 2 M12x40x1.75 Bolt, Nut, Lock Washer and Washer (30 mm OD)
R 1 M14x90x2.00 Bolt, Nut, Nyloc Nut, and x2 Washers (27 mm OD)
For use with either
ZF Flange neck option – ZF2006A. Note: This towbar must be used with either a Witter Towball (part number Z11) or Class
A50-1 or A50-X towball dimensionally Conforming to A50-1 with a 'D' and 'S' value greater than or equal to that of the towbar.
ZQ Detachable neck option – ZQ2006A. Please refer to ZQ fitting instructions for installation.
FITTING
1. Ensure the box contains every item as listed above.
2. Lower the exhaust from the upper hanger and remove the black plastic underskirt. (x2 torq screws on the bottom edge of the skirt,
x1 central nut, and x5 screws connecting the heat shield. At this point pull the heat shield and underskirt from under the
bumper edge to gain access to the x2 horizontal nuts fixing the skirt to the rear panel.)
3. Loosely attach the LHS and RHS Plates (B and D) to the chassis rails using fixings (J), ensuring the Spacer Plate (G) is sandwiched
between the chassis rail and side arm.
4. Slide the Cross Bar (A) under the bumper and loosely attach to side plates (B and D) using the relevant fixings. Ensure Cross Bar (A) is
in its correct position and fully tighten the rear most fixing (J) on the off side. This is due to clearance being restricted once Bracket (E) is
in place.
5. Attach Support Brackets (F & E) to the chassis rail and Side Brackets using the relevant fixings. Relocate the exhaust hanger using
fixing (R) and attach to Side Plate (D). Please ensure the washers support the hanger and the Nyloc Nut is threaded onto the bolt last.
6. Attach preferred neck and fasten the Electrical Plate (ZEP1) behind the Face Plate Electrical Plate Bracket (ZEP2) following the
additional fitting instruction provided. Alternatively use the bracket (ZEQ2) and fixing (H) and attach to the cross bar. If this option is
chosen, it may be necessary to turn the Electrical Plate upside down and pivot the Electrical Plate towards the ground slightly in order to
avoid possible contact with the underside of the bumper. Fully tighten all remaining fixings to the recommended torque setting.
7. Ensure the Face Plate is vertical and fully tighten all fixings to the recommended torque settings and cut the under skirt as illustrated
bellow (x2 Slots, symmetrical to the centre line of the bumper, 10 mm wide by 65 mm deep) and refit in reverse .
Recommended torque settings: Grade 8.8 bolts: M8 - 27Nm, M10 - 53 Nm, M12 - 95 Nm, M14 - 150 Nm, M16 - 214
Nm Grade 10.9: M12 – 139Nm, M10 – 78Nm
Fitting
Instructions
µW0001C34AU-FIT$010809100000(Ä
W 0 0 0 1 C 3 4 A U -F IT $ 0 1 0 8 0 9 1 0 0 0 0 0
For TOWBAR
For CITROEN C5 HATCHBACK
2004 - 2008
Please refer to vehicle
specification for the trailer
weight and nose Limits,
which must be observed
C34AU
for
C34A
C34AQ
C34AQF