SCHOLTES HSD 98 Mode D'emploi page 13

CONTROLS
Model HSD 98 BK
To select the functions of the hood just touch the commands.
Light key ON/OFF
Intensive speed selection key (suction power) - duration 5
minutes - press again to return to previous setting.
High-speed selection key (suction power).
Medium-speed selection key (suction power) - when
flashing it indicates the need to wash or replace the carbon
filter. This signal is normally deactivated. Press keys 1 and 2
at the same time to activate it. At first only key 1 will flash and
then both keys 1 and 2 to indicate activation. Repeat the
operation to deactivate the signal. At first keys 1 and 2 will
flash and then only key 1 to indicate deactivation.
Low-speed selection key (suction power) – when flashing it
indicates the need to wash the fats filter.
Motor key OFF (stand by) – excludes the electronics – reset
wash/replace filters signals.
MOTOR OFF
Press briefly to switch the motor off.
RESET FILTERS SIGNALS
After having carried out maintenance of the filters, press the
key for 3 seconds. Flashing led 1 (fats filter) or 2 (carbon filter)
will stop flashing.
EXCLUDING THE ELECTRONICS
Press the key for 3 seconds. The hood command electronics
will be excluded.
This function can be useful during the product cleaning
operations.
Just repeat the operation to reinsert the electronics.
If the hood fails to operate correctly, briefly disconnect it from the mains power
supply for almost 5 sec. by pulling out the plug. Then plug it in again and try once
more before contacting the Technical Assistance Service.
Model HSD 98 - HSD 98 IX/BK
1. Reset Button for saturation of filters: the hood will
warn the user that it is time to do maintenance work on
the filters, by giving out a light-signal.
Red-light Button blinking: carry out the maintenance
of the greasy filters, following this press the button for
over 3 seconds and the button will turn off.
Red-light Button: carry out maintenace on carbon-
filters, following this press the button for more than 3
seconds, the button will switch off.
Attention: the hood is provided only with a warning
signal for greasy filters.
To put into function the greasy-filter signal:: Set the
cooker-hood off, press switch button no.6 for more than
3 seconds ( the switch will turn on red signalling that
the function has been set.
To disactivate the carbon filter signal, repeat the entire
procedure again.
2. Speed selecting button (speed rating) for intensive
suction (with timer): press to select the suction-speed
(rating) , the functioning-time is 5 minutes (blinking
push-button) , following this the suction function will
either turn off or return to the suction-speed that had
previously been selected.
Note: It is possible to keep a check of this function so
that the hood switches off 5 minutes after it has worked,
(even though another function had been selected prior
to this one) after having pressed the button, press again
and keep pressed , the pilot-light will start blinking
indicating that the selected function has been set..
3. Speed selecting button suction speed 3: press this
switch once to select the speed rating of suction speed,
press again and keep pressed to activate the time-
function for 10 minutes (blinking light) following this the
cooker-hood will switch off..
4. Speed selecting button suction speed 2: press this
switch once to select the speed rating of suction speed,
press again and keep pressed to activate the time-
function for 15 minutes (blinking light) following this the
cooker-hood will switch off.
5. Switch OFF suction / ON speed (rating) of suction
speed 1: press this switch once turn off the speed
(rating) of suction function that has been selected or (if
no speed rating of suction function select the speed
(rating) of suction speed 1, press again and keep
pressed to activate the time-function for 20 minutes
(blinking light), following this the cooker hood will swittch
off.
6. Switch ON/OFF Pilot-lights: press to switch on/off
lights.
EN
13