Publicité
Les langues disponibles
Les langues disponibles
- If you use two coffee pads at the same
time, firmly press the first coffee pad
into the recess of the coffee pad cassette
with the paper edge facing upwards.
Subsequently, put the second coffee pad
into the coffee pad cassette according to
the instructions above.
•
Fill the water reservoir (12) with water up
to the maximum mark ("MAX") on the
water level indicator (13).
•
Place the water reservoir (12) into the
appliance.
•
Set the locking collar (7) to position 'C'.
•
Remove the coffee pad cassette (11) from
the appliance.
•
Put the coffee pad in the coffee pad
cassette (11).
- For one cup, put the coffee pad in the
side marked '1' on the coffee pad
cassette (fig. C1).
- For two cups, put the coffee pads in the
side marked '2' on the coffee pad
cassette (fig. C2).
•
Insert the coffee pad cassette (11) into the
appliance with the coffee pad upwards.
Make sure that the coffee pad does not
shift.
•
Set the locking collar (7) to position 'A' as
close as possible (see arrow in fig. B).
•
Place the required amount of cups under
the coffee dispenser (8).
- For one cup, place the cup under both
dispenser nozzles of the coffee
dispenser.
- For two cups, place one cup under the
left dispenser nozzle and one cup under
the right dispenser nozzle of the coffee
dispenser.
•
Press the on/off button (1) to switch on
the appliance. The ready-to-brew indicator
(5) lights red. The appliance starts heating.
If the process is completed, the ready-to-
brew indicator (5) lights green.
•
Take one of the following actions:
- For one cup, press the start/stop button
(2). The appliance starts making coffee.
To interrupt the process, press the start/
stop button (2) again.
- For two cups, press the start/stop button
(3). The appliance starts making coffee.
To interrupt the process, press the start/
stop button (3) again.
•
If the process is completed, set the locking
collar (7) to position 'B'.
•
Press the on/off button (1) to switch off
the appliance.
•
Allow the appliance to cool down completely.
Pre-brewing function
The pre-brewing function makes sure that the
appliance initially only supplies a small quantity
of water. The coffee-making process continues
after a short interval.
Programming the coffee quantity
(fig. A - C)
The appliance features a convenient function for
programming the required quantity of coffee
individually for both start/stop buttons (2/3).
You can change the coffee strength according
to your taste.
Note: The programming mode is active for
approximately 30 seconds after pressing start/
stop button (2) or approximately 60 seconds
after pressing start/stop button (3). If you do
not press the start/stop button (2/3) before
the brewing cycle stops automatically, the
maximum coffee quantity will be programmed.
•
Put the coffee pad in the coffee pad
cassette (11). Insert the coffee pad cassette
(11) into the appliance. Refer to the
section "Making coffee with coffee pads".
•
Set the locking collar (7) to position 'A' as
close as possible (see arrow in fig. B).
•
Place one or two large cups onto the cup
tray (14).
•
Press the on/off button (1) to switch on
the appliance. The ready-to-brew indicator
(5) lights red. The appliance starts heating.
If the process is completed, the ready-to-
brew indicator (5) lights green.
•
Keep the start/stop button (2/3) pressed for
3-4 seconds until the ready-to-brew indicator
(5) flashes green. The programming mode is
active. The appliance starts making coffee.
•
If the required coffee quantity is obtained,
press the same start/stop button (2/3)
again. The appliance stops making coffee.
The brewing time is programmed.
10
Publicité
