Ferroli DIVAtech F 32 D Instructions D'utilisation, D'installation Et D'entretien page 34

Connection with separate pipes
C
5x
fig. 11 - Examples of connection with separate pipes (
Table. 4 - Typology
Type Description
C1X Wall horizontal exhaust and intake. The inlet/outlet terminals must be concentric or close enough to be
undergo similar wind conditions (within 50 cm)
C3X Roof vertical exhaust and intake. Inlet/outlet terminals like for C12
C5X Wall or roof exhaust and intake separate or in any case in areas with different pressures. The exhaust
and intake must not be positioned on opposite walls.
C6X Intake and exhaust with separately certified pipes (EN 1856/1)
B2X Intake from installation room and wall or roof exhaust
IMPORTANT - THE ROOM MUST BE PROVIDED WITH APPROPRIATE VENTILATION
For connection of the separate ducts, fit the unit with the following starting accessory:
80
fig. 12 - Starting accessory for separate ducts
Before installation, check the baffle to be used and make sure the maximum permissible
length has not been exceeded, by means of a simple calculation:
1. Establish the layout of the system of split flues, including accessories and outlet ter-
minals.
2. Consult the table 6 and identify the losses in m
ponent, according to the installation position.
3. Check that the sum total of losses is less than or equal to the maximum permissible
length in table 5.
Table. 5 - Baffles for separate ducts
Max. permissible length
Baffle to use
34
EN
B C
2x 1x
= Air / = Fumes)
80
010011X0
(equivalent metres) of every com-
eq
DIVAtech F 32 D
48 m
eq
0 - 15 m Ø 45
eq
15 - 35 m Ø 50
eq
35 - 48 m No baffle
eq
cod. 3541A771 - Rev. 00 - 09/2013
DIVAtech F 32 D
Table. 6 - Accessories
PIPE 0.5 m M/F
1 m M/F
2 m M/F
BEND 45° F/F
45° M/F
90° F/F
90° M/F
90° M/F + Test point
Ø 80
PIPE SECTION with test point
for condensate drain
TEE for condensate drain
TERMINAL air, wall
fumes, wall with antiwind
FLUE Split air/fumes 80/80
Fume outlet only Ø80
REDUCTION from Ø80 to Ø100
from Ø100 to Ø80
PIPE 1 m M/F
Ø 100 BEND 45° M/F
90° M/F
TERMINAL air, wall
fumes, wall with antiwind
PIPE 1 m M/F
BEND 90° M/F
Ø 60
REDUCTION 80 - 60
TERMINAL fumes, wall
ATTENTION: CONSIDER THE HIGH PRESSURE LOSSES OF Ø60 ACCESSORIES; USE
THEM ONLY IF NECESSARY AND AT THE LAST FUME EXHAUST SECTION.
Connection to collective flues
C
8X
fig. 13 - Examples of connection to flues (
Table. 7 - Typology
Type Description
C2X Intake and exhaust in common flue (intake and exhaust in same flue)
C4X Intake and exhaust in common and separate flues , but undergoing similar wind conditions
C8X Exhaust in single or common flue and wall intake
B3X Intake from installation room by means of concentric duct (that encloses the exhaust) and exhaust in
common flue with natural draught
IMPORTANT - THE ROOM MUST BE PROVIDED WITH APPROPRIATE VENTILATION
If the boiler is to be connected DIVAtech F 32 D to a collective flue or a single flue with
natural draught, the flue or chimney must be expressly designed by professionally qual-
ified technical personnel in conformity with the current regulations and be suitable for
sealed chamber units equipped with fan.
Losses in m
Air Fume exhaust
inlet
Vertical
1KWMA38A 0.5 0.5
1KWMA83A 1.0 1.0
1KWMA06K 2.0 2.0
1KWMA01K 1.9
1KWMA65A 1.9
1KWMA02K 2.0
1KWMA82A 1.5
1KWMA70U 1.5
1KWMA16U 0.2
1KWMA55U -
1KWMA05K -
1KWMA85A 2.0
1KWMA86A -
1KWMA84U -
1KWMA83U + -
1KWMA86U
1KWMA03U 0.0
1.5
1KWMA08K 0.4 0.4
1KWMA03K 0.6
1KWMA04K 0.8
1KWMA14K 1.5
1KWMA29K -
010028X0 - 2.0
010029X0 -
010030X0 -
1KWMA90A -
C
4X
C
2X
= Air / = Fumes)
eq
Horizontal
1.0
2.0
4.0
2.9
2.9
3.0
2.5
2.5
0.2
3.0
7.0
-
5.0
12.0
4.0
0.0
3.0
0.8
1.0
1.3
-
3.0
6.0
6.0
8.0
7.0