Husqvarna AUTOMOWER 405 Guide Rapide page 6

QUICK GUIDE
A
Placement of and connecting the
charging station
1. Place the charging station at a central position in the
working area, with a lot of open space in front of the
charging station and on a relatively horizontal surface.
2. Connect the power supply's low voltage cable to the
charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the robotic lawn mower in the charging station to
charge the battery while the boundary wire is laid. Press
the ON/OFF button for 3 seconds and make sure that the
indicator lamp on the button is lit.
B
Placement of the boundary wire and the
guide wire
1. Lay the boundary wire so that it forms a loop around the
working area.
2. Make an eyelet at the point where the guide wire will later
be connected.
3. Run the guide wire to the point on the boundary loop where
the connection will be made. Avoid laying the wire at tight
angles.
C
Connecting the boundary wire and the guide
wire
1. Narrow passages in the yard make it difficult for the robotic
lawn mower to find the charging station. The robotic lawn
mower can be lead to remote areas using the guide wire.
The guide wire also helps the robotic lawn mower to
quickly find the charging station.
2. Lay the guide wire under the charging station and at least
2 m / 7 ft straight out from the front edge of the charging
station.
3. Open the connectors and lay the wire ends in the recesses
on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8"
above the connectors.
6. Press the connectors onto the contact pins, marked AL
(left) and AR (right), on the charging station. It is important
that the right-hand wire is connected to the right-hand
contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the connector to the contact pin marked G1 on the
charging station.
D
Connecting the guide wire to the boundary
wire
1. Cut the boundary wire with a wire cutters at the centre of
the eyelet that was made in step B.2
2. Connect the guide wire to the boundary wire using the
accompanying couplers. Press the couplers completely
together with a polygrip.
QG_P16_1142655_2022.indd 6 QG_P16_1142655_2022.indd 6
Starting and stopping
STARTING
1. Open the cover by pressing the STOP button.
2. Press the ON/OFF button for 3 seconds. When you do this
for the first time, a start up sequence starts where you
select a four digit PIN code among other things.
3. Press the START button and close the cover.
STOPPING
Press the STOP button.
Adjusting the robotic lawn mower to suit the
size of your lawn
The mowing results depend on the mowing time. Adjust
the mowing time to suit your yard using the Schedule
function. You decide what times during the day the
robotic lawn mower is to work.
Use the Weather Timer function and the robotic lawn
mower will automatically adjust the mowing time to the
growth of the grass.
Maintenance
• Press the ON/OFF button for 3 seconds to disable the
product and check that the indicator lamp on the button
is not lit before all work on the robotic lawn mower's
chassis, such as cleaning or replacing the blades.
Replace the blades regularly for the best mowing result.
• Never use a high-pressure washer to clean the robotic
lawn mower. Never use solvents for cleaning. Clean the
product with a brush or running water from a water hose.
• All connections to the charging station (power supply,
boundary and guide wire) must be disconnected if there
is a risk of a thunderstorm.
• Fully charge the battery at the end of the season before
winter storage.
For more information and instructions, read the
complete Operator's manual on
www.husqvarna.com.
en
2021-06-21 12:15:45 2021-06-21 12:15:45