Silverline 360375 Guide Rapide

Heavy Duty Hand Cable Puller
3500kg / 3m Cable
FR Palan-tendeur de traction usage intensif
DE Schwerlast-Greifzug
ES Polipasto de tracción de gran capacidad
IT Estrattore cavo a sollecitazione severa
NL 'Heavy-Duty' hand treklier
PL Wytrzymała ręczna wciągarka kablowa
FIG. I
GB
Specifications
Cable: Ø6.0mm x 3m
*Max. usable distance: (Primary) 2000mm
(Secondary) 3500mm
Leverage ratio: 15:1
Pulling
*Max. pulling weight on
horizontal surface: 35kN
Rated horizontal pulling force: 1100 daN
Note: *Max. pulling weight on horizontal surface is given as a rolling load on a level surface. Exercise extreme caution
and do not overload, particularly on "deadweight" loads.
General Safety
WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in a
serious injury.
WARNING: This tool is not intended for use by persons (including children) with reduced, physical or mental
capabilities or lack of experience or knowledge unless they have been given supervision or instruction concerning use
of the tool by a person responsible for their safety. Children must be supervised to ensure that they do not play with the tool.
Save all warnings and instructions for future reference.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
c) Keep children and bystanders away while operating or using this tool. Distractions can cause you to lose control.
2) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating or using this tool. Do not operate or
use the tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while
operating or using the tool may result in serious personal injury. Work sensibly at all times with regular breaks if necessary.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Remove any adjusting key or wrench before operating the tool. A wrench or a key left attached to a rotating part of the
tool may result in personal injury.
d) Do not overreach. Keep proper footing and balance at all times. This enables better control of the tool in unexpected
situations.
e) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught in moving parts.
3) Tool use and care
IMPORTANT: Tools used outdoors may require more regular cleaning and surface treatment to prevent corrosion, as well as
replacement grease or oil on moving parts to maintain them in good working condition.
a) Maintain tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that
may affect the tool's operation. If damaged, have the tool repaired before use. Many accidents are caused by poorly
maintained tools.
b) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
c) Use the tool's accessories and tool bits etc. in accordance with these instructions, taking into account the working
conditions and the work to be performed. Use of the tool for operations different from those intended could result in a
hazardous situation.
4) Service
a) Have your tool serviced or repaired by a qualified repair person using only identical replacement parts. This will
ensure that the safety of the tool is maintained.
Product Familiarisation
Pulling Tool Safety
1) Direction Switch
Ensure your cable puller is maintained in a safe working condition. Observe the following important guidance:
2) LED Light
• Operate using manual force only. Do not attempt to use external objects to increase leverage at the handle.
3) Bit Holder
• Before each use, check the condition of the equipment. Pay particular attention to cables and locking mechanisms
4) Battery Level Indicator
• Cables should be free from kinks and should not show any evidence of fraying or cutting
5) Ratchet Drive Spring
• Locking mechanisms should work freely and should be clean of excessive dirt or grease
6) Cable
• Ensure the safety latches on the hooks are closed and the load is secure before pulling commences
7) Cable Hook
• Test all safety devices (including automatic) before use
8) Handle
9) Secondary Cable Hook • DO NOT operate the puller with less than 3 wraps of cable on the spindle.
• DO NOT attempt to pull items around or over a corner
10) Hook Mounting Bracket
• DO NOT wrap cable around any object DIRECTLY and hook it back on itself
• DO NOT OVERLOAD: Ensure the weight of all loads is within the capacity of this equipment (see specification)
• DO NOT LIFT with this puller. This equipment is not designed to hoist. The puller is only designed to be used on a
horizontal surface.
• When pulling, allow for rolling resistance which will significantly increase the weight of an object – particularly in cases
when pulling through mud, snow or water
• Use an adequate sling, eyebolt or other attachment on the load to be pulled and ensure that there is a positive
engagement of the puller hook to the load
• Do not use a pipe, lever or other device to lengthen the handle for additional leverage; the pulley may fail, causing
damage and/or personal injury
• Under no circumstances use pulling equipment to pull people or objects with people attached
• Do not modify any pulling equipment. Any attempt to tamper with this equipment will invalidate its guarantee, and could
result in serious injury to yourself or others around you
• Pulling equipment should be inspected by a qualified person at least once each year and the results of the inspection
recorded in an inspection book for future reference
• If you are in any way unsure about the safe method of using this equipment, do not use it
• Assembly, maintenance, or independent operation of appliances may be assigned by persons who are suitable for and
familiar with these procedures.
• The operation guide is available and accessible to persons who are in charge of assembly, maintenance or independent
operation of appliance.
• Moving loads:
• The operator may start moving a load only after determining it is clear that the load is safely secured, and that no persons
remain are in the danger area, or after confirmation has been received from the chainer.
• The operator must keep an eye on all load movements.
• If the operator is unable to keep an eye on all load movements, suitable measures must be taken not to put bystanders in the
vicinity of the load at risk.
Intended Use
Hand-powered cable puller to aid in pulling procedures. Suitable for non-commercial, light-to-medium duty use only.
WARNING: NOT FOR LIFTING! NOT FOR LASHING! FOR PULLING ONLY!
Note: This product is not suitable for industrial use.
Unpacking Your Tool
• Carefully unpack and inspect your new tool. Familiarise yourself with all its features and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing or damaged, have such parts
replaced before attempting to use this tool.
Operation
WARNING: ALWAYS wear eye protection, as well as suitable cut-proof gloves, when working with this tool.
4
3
2
1
Attaching the cable puller
1. Attach the Secondary Cable Hook (9) onto the item to be pulled. Ensure the total load will not exceed 1750kg
2. Check the item is securely attached and the Safety Bar (2) is closed
3. Slide the Ratchet Drive Spring (5) across to the disengaged position so that the Handle (8) does not engage the Ratchet
Teeth (4)
4. Press the Ratchet Lock Lever (3) and unwind sufficient Cable (6) from the spool to attach the Fixed Hook (1) to the anchor
position. Release the Ratchet Lock Lever. Ensure hooks are securely attached and Safety Bar is closed (Fig. I)
Pulling capacity:
Note: To achieve the maximum pulling capacity of this cable puller (3500kg). The cable length will be shortened to approx.
half the original length.
• Attach the Secondary Cable Hook (9) to the Hook Mounting Bracket (10)
• Use the Secondary Cable Hook to attach to the pulling device
• Follow instructions provided under 'Attaching the Cable Puller'
• Use the Cable Hook (7) to attach the cable puller to the load
Pulling
• Slide the Ratchet Drive Spring (5) across to the engaged position so that the Handle (8) engages the Ratchet Teeth (4)
• Crank the Handle (8) backwards and forwards to tension the cable and pull the load
Releasing the tension
1. Slide the Ratchet Drive Spring (5) across to the disengaged position so that the Handle (8) does not engage the Ratchet
Teeth (4)
2. Carefully move the Handle (8) until the drive pawl pushes and disengages the stop pawl and clears the Ratchet Teeth. Then
move the Handle in the opposite direction, to release the load by one notch
3. Repeat this handle motion as often as required, to release the tension one notch at a time, until enough slack has been
provided to remove the hooks
4. Ensure the load is stable and secure before removing Fixed Hook (1) and Cable Hook (7)
WARNING: When releasing tension, avoid abrupt handle movements. Apply pressure to the Handle evenly and with a
smooth action. Abrupt movements can cause the load to shift, making it unstable
Accessories
• A range of accessories and consumables, including Safety Hard Hat (306429), and Expert Rigger Gloves (633501), is
available from your Silverline stockist. Spare parts can be obtained from toolsparesonline.com
Maintenance
General inspection
• Regularly check that all the fixing screws are tight
• Keep the Cable Puller clean and in good order. Store with the cable fully wound on the spool
• Carry out a visual inspection every time the Cable Puller is used and listen for any unusual sounds during operation
• Store in a safe, secure and dry place out of the reach of children
• Never disassemble the Cable Puller
• Inspect the mechanism before every use
Certificate of Conformity
Identification code: 360375
Description: Heavy Duty Hand Cable Puller
Diameter of the lashing steel wire rope: . . . . . . . . . . . . Ø6.0mm x 3m (L)
Date: 22/08/15
Name and address of the manufacturer:
Powerbox International Limited, Company No.06897059.Registered address: Boundary Way, Lufton Trading Estate,
Yeovil, Somerset BA22 8HZ, United Kingdom
360375
Vesion date: 05.05.2017
5
6
7
8
9
10
silverlinetools.com