Pioneer Elite PRO-1010HD Mode D'emploi page 41

3 LOW 2 3 MID LOW 2
3 MANUAL/**2 3 HIGH 2
¶ LOW
......... Provides yellowish color tone with low
warmth.
¶ MID-LOW
... Provides a color tone between MID and
LOW.
¶ MID
......... Provides natural color tone (Standard).
¶ MID-HIGH ... Provides color tone between HIGH and
MID.
¶ HIGH
......... Provides a bluish, very warm color tone.
¶ MANUAL/**... Saves desired adjusted color
temperature settings.
The abbreviations of the color tone modes on which
manual adjustments are based are indicated in the **
section as shown below.
LOW -> LO, MID LOW -> ML, MID -> MD, MID HIGH ->
MH, HIGH -> HI
R. HIGH ... Adjusts the red of bright parts
G. HIGH ... Adjusts the green of bright parts Becomes softer Becomes stronger
B. HIGH ... Adjusts the blue of bright parts
R. LOW ... Adjusts the red of dark parts
G. LOW ... Adjusts the green of dark parts
B. LOW ... Adjusts the blue of dark parts
Notes
÷ This setting is not possible when in the DYNAMIC mode in [AV
SELECTION].
÷ If you adjust R. HIGH, G. HIGH, B. HIGH, R. LOW, G. LOW or
B. LOW, COLOR TEMP . automatically switches to MANUAL/
**.
÷ R. HIGH, G. HIGH, B. HIGH, R. LOW, G. LOW and B. LOW
adjustment values are reflected in COLOR TEMP . MANUAL/**
settings. The values are not reflected if anything other than
MANUAL/** is selected.
When adjusting color temperature to desired settings
1 With COLOR TEMP ., use the 2/3 buttons to set the
color temperature close to that desired, then press the
SET button.
2 With R. HIGH, G. HIGH, B. HIGH, R. LOW, G. LOW or
B. LOW, use the 2/3 buttons to make fine
adjustments to the settings made in 1, then press the
SET button.
3 The adjusted values made in 2 in COLOR TEMP .
MANUAL/** is saved.
¶ Setting items during PC signal input
GRADATION
This function sets picture γ characteristics.
Each time you press the 2/3 buttons, the setting
changes as follows:
3 GAMMA1.8 2
3 GAMMA2.2 2
3 MID 2
3 MID HIGH 2
Decrease Increase
Becomes softer Becomes stronger
Becomes softer Becomes stronger
Becomes softer Becomes stronger
Becomes softer Becomes stronger
Becomes softer Becomes stronger
3 GAMMA2.0 2
Picture and Screen Adjustment
¶ GAMMA1.8 ... Provides a brighter γ setting than
standard.
¶ GAMMA2.0 ... Provides standard brightness γ
characteristics.
¶ GAMMA2.2 ... Provides darker γ characteristics than
standard.
The following functions make fine adjustments to color
temperature (white color tone).
R. HIGH ... Adjusts the red of bright parts
G. HIGH ... Adjusts the green of bright parts Becomes softer Becomes stronger
B. HIGH ... Adjusts the blue of bright parts
R. LOW ... Adjusts the red of dark parts
G. LOW ... Adjusts the green of dark parts
B. LOW ... Adjusts the blue of dark parts
Picture Adjustment (3)
You can save picture adjustment values for each INPUT
and each AV SELECTION mode.
MENU
5/∞
2/3
SET
Display operating Remote control unit
panel
1
Press the AV SELECTION button to select the
desired mode (Refer to page 33).
2
Press the MENU button to display the menu.
STANDARD
PICTURE SCREEN
CONTRAST
BRIGHTNESS
COLOR
TINT
SHARPNESS
MPEG NR
DNR
CTI
PICTURE RESET
ENTER
SET
Decrease Increase
Becomes softer Becomes stronger
Becomes softer Becomes stronger
Becomes softer Becomes stronger
Becomes softer Becomes stronger
Becomes softer Becomes stronger
MENU
2/3
SET
5/∞
AV
SELECTION
INPUT1
SETUP OPTION
:
0
:
0
:
0
:
0
:
0
:
MID
:
MID
:
ON
EXIT
MENU
37
EN