USING YOUR DYSON APPLIANCE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
OPERATION
•
Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
•
Ensure the appliance remains upright in use. Dirt and debris may be released if
it is turned upside down.
•
Do not operate while checking for blockages as doing so may result in
personal injury.
•
For domestic indoor and car use only. Do not use it while the car is in motion or
while driving.
•
To operate the max mode, hold the trigger down and press the boost button.
The 'max' button will light up.
•
To switch off max mode, hold the trigger down and press the max button again.
Note: The appliance will retain the last used mode. So if you use it in max mode
and do not disengage it, the appliance will operate in max mode when it is next
used until you depress the max button to disengage it.
•
This appliance has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
•
To watch a short online video visit:
www.dysoncanada.ca/sv09gettingstarted
DOCKING STATION INSTALLATION
•
Use appropriate mounting hardware for your wall type and ensure that the
docking station is mounted securely. Ensure no pipe work (gas, water, air) or
electrical cables, wires or ductwork are located directly behind the mounting
area. The docking station must be mounted in accordance with regulations
and applicable codes/standards (provincial and local laws may apply). Dyson
recommends the use of protective clothing, eyeware and materials when
installing the docking station.
CARPETS OR HARD FLOORS
•
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
•
The brush bar on the appliance can damage certain carpet types and floors.
Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming without the motorized floor tool and
consulting with your flooring manufacturer.
•
Before vacuuming highly polished floors, such as wood or linoleum, first check
that the underside of the floor tool and its brushes are free from foreign objects
that could cause marking.
LOOKING AFTER YOUR DYSON APPLIANCE
•
Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
•
Only use parts recommended by Dyson. If you do not this could invalidate
your warranty.
•
Store the appliance indoors. Do not use or store it below 3˚C (37.4˚F). Ensure
the appliance is at room temperature before operating.
•
Clean the appliance only with a dry cloth. Do not use any lubricants, cleaning
agents, polishes or air fresheners on any part of the appliance.
VACUUMING
•
Do not use without the clear bin and filters in place.
•
Fine dirt such as flour should only be vacuumed in very small amounts.
•
Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
•
When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimize any effect from this, do not put your hand or
insert any object into the clear bin unless you have first emptied it. Clean the
clear bin with a damp cloth only. (See 'Cleaning the clear bin'.)
•
Use extra care when cleaning on stairs.
•
Do not rest the appliance on chairs, tables, etc.
•
Do not press down on the nozzle with excessive force when using the appliance
as this may cause damage.
•
Do not leave the cleaner head in one place on delicate floors.
•
On waxed floors the movement of the cleaner head may create an uneven
lustre. If this happens, wipe with a damp cloth, polish the area with wax, and
wait for it to dry.
11.11.2014 11:09 - C67726_GENE_OPMAN_CA_X480-SV09-V6-ABSOLUTE-OPMAN-67726.indd_15_4c0s
DIAGNOSTICS - MAIN BODY
When in use, trigger pressed:
Solid blue: MAX mode 'ON'.
Light off: Powerful suction.
Flashing blue: Low battery warning.
Fast flashing blue: No power, temporary
fault (e.g. check filter or for blockages).
EMPTYING THE CLEAR BIN
•
Empty as soon as the dirt reaches the level of the MAX mark – do not overfill.
•
Ensure the appliance is disconnected from the charger before emptying the
clear bin. Be careful not to pull the 'ON' trigger.
•
To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
•
To release the dirt, push the red button by the clear bin: Press once to open the
bin base. Press a second time to release the clear bin from the main body of
the appliance.
•
To minimize dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
•
Remove the clear bin carefully from the bag.
•
Seal the bag tightly, dispose as normal.
•
Close the clear bin base so it clicks into place and is secure.
CLEANING THE CLEAR BIN
•
Ensure the appliance is disconnected from the charger before removing the
clear bin. Be careful not to pull the 'ON' trigger.
•
Remove the wand and floor tool.
•
Push the red button by the clear bin: press once to open the bin base. Press a
second time to release the clear bin from the main body of the appliance.
•
Remove the clear bin carefully.
•
Clean the clear bin with a damp cloth only.
•
Do not use detergents, polishes or air fresheners to clean the clear bin.
•
Do not put the clear bin in a dishwasher.
•
Clean the cyclone shroud with the brush on the combination tool to remove lint
and dust.
•
Ensure the clear bin is completely dry before replacing.
•
To replace the clear bin, push the clear bin up and in to the main body of the
appliance. It will click into place.
•
Close the clear bin base so it clicks into place and is secure.
WASHING THE FILTERS
•
Your appliance has two washable filters; wash the filters at least once a month
according to the following instructions to maintain performance. More frequent
washing may be required where the user: vacuums fine dust, operates mainly in
'Powerful suction' mode, or uses the machine intensively.
WASHING FILTER A
•
Ensure the appliance is disconnected from the charger before removing the
filter. Be careful not to pull the 'ON' trigger.
•
To remove the filter, lift it out of the top of the appliance.
•
Check and wash the filter regularly according to instructions to
maintain performance.
•
The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'POWERFUL SUCTION' mode.
•
Wash the filter with cold water only.
•
Run water over the outside of the filter until the water runs clear.
•
Squeeze and twist with both hands to make sure the excess water is removed.
•
Lay the filter on its side to dry. Leave to dry completely for a minimum of
24 hours.
•
Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near an open flame.
•
To refit, place the dry filter back into the top of the appliance. Make sure it is
seated properly.
•
To watch a short online video, visit:
www.dysoncanada.ca/sv09filterwash
13