Sammic SL-19D Mode D'emploi page 5

Microswitch setting tabe (SL-19D and SL-20D):
C
YCLE T L C T
HERMAL OCK YCLE YPE
Nº T
IME
( )
SEC
M 1 M
ICROSWITCH ICROSWITCH
120
5 OFF OFF
210
120
6 ON OFF
210
Control of cycle time (Thermal Lock) as a function
of the boiler temperature:
The electronic controller features the possibility
of increasing the cycle time until the preset tem-
perature is reached in the boiler. So, in the event
the temperature of the boiler were lower than the
preset value, the cycle would be extended until
the preset temperature is reached. This prevents
rinsing with cold water. In order to enable this
feature, select the appropriate digit from the
enclosed table.
OPERATION
Start-up
1. Open the 3/4" stopcock to allow water to enter
the machine.
2. Turn on the magnetothermal switch that pro-
tects the installation.
3. Check that the filters and the drain plug are in
place, as Figure "C" shows.
4. Turn the main switch (Fig. A-1) to the ON
position for the automatic filling of the wash
tank and the connection of the heater ele-
ments.
5. The light indicator (Fig.A-e) turns on when the
washing temperature (55º/ 60ºC) has been
reached.
6. Start Cycle:
-Place the objects to be washed in a basket
(rack).
-Close the door.
-Select the washing programme by pressing
key "select cycle" (Fig. A-2).
-Press the Start Cycle key (Fig. A-3). The was-
hing phase indicator light (Fig. A-a) turns on.
The machine completes the entire washing
cycle. If you press the Start Cycle key (Fig. A-
3) again during the washing phase, the pro-
gramme immediately shifts to the rinsing pro-
cess. Pressing the said key during the rinsing
phase causes the machine to stop.
7. When the complete cycle has finished, the two
indicators (Fig. A-a) and (Fig. A-b) flash.
Detergent dispenser
The glasswasher is prepared for its fitting with an
adjustable detergent dispenser, the part number
of which appears on the spare parts list. This dis-
penser has to be installed in the machine base, at
the front, as shown on the exploded view. At the
rear of the wash tank, there is an opening where
to insert the detergent injection nozzle.
The dispenser delivers about 0.7ml/s of deter-
gent (maximum). At the first filling of the tank,
feeding of detergent is roughly 119ml in 170s,
resulting in a maximum concentration of 3ml/l.
At each cycle, the dispenser delivers 10ml of
detergent. It is possible to reduce or increase the
injected quantity by turning the adjusting screw
W
ATER SOFTENER
on the dispenser.
2 M 3
ICROSWITCH
ON
Rinsing aid dispenser
ON
Verify that the rinsing aid reservoir is full. Start
and stop the washing water pump 5 or 6 times by
pressing the "Start Cycle" (Fig. A-3) and check
whether the tube fills up with rinsing aid and
goes in the boiler. Setting the dispenser is done
by turning an adjusting screw on the front lower
panel in the direction shown on the panel graph.
In order to determine whether the amount of rin-
sing aid is adequate, look at the glasses against
the light. If there are water droplets on the glass,
the amount of rinsing aid is insufficient; if stre-
aks develop, the quantity of rinsing aid is too
much.
Machine Draining
Open the door and take out the drain plug, lea-
ving the filters in place. Water will fall by gravity,
dirt accumulating in the filters.
Water Softener. Regeneration Cycle.
Regnerate the descaler every 30 or 50 rinsing
cycles approximately.
1. Drain the wash tank completely. MACHINE
EMPTY WITHOUT DRAIN PLUG.
2. With the door open, press "Select Cycle" (Fig.
A-2), the "Regeneration" LED (Fig. A k) turns
on, meaning the machine is ready for the
regeneration cycle.
3. Close the door and press "Start cycle" (Fig. A-
3) to start the regeneration cycle.
4. The "Regeneration" LED (Fig. A-k) starts flas-
hing and the regeneration cycle starts after 6
seconds. During those 6 seconds, you can
stop the cycle by pressing "Start cycle" (Fig. A-
3) again.
5. This cycle lasts 23 minutes and cannot be
stopped. The "Regeneration" LED (Fig. A-k)
remains ON until the cycle finishes.
6. When the "Regeneration" LED (Fig. A-k) turns
off, switch the machine off.
Water Softener. Refilling regenerating salt.
The regenerating salt container is accessible
through the inside of the wash tank. To refill the
salt container:
1. Drain the wash tank completely.
2. Check to see if there is any salt left in the con-
tainer. Add kitchen salt as and when necessary
to fill the container. A full container permits
three regeneration cycles.
Boiler Draining
1. Drain the wash tank.
2. Close the water inlet.
3. Remove the tube coming from the rinsing aid
pump from the inlet connector to the boiler
and place a container under the boiler. All
water flows out of the boiler by gravity.
Tank cleaning
The tank should be cleaned after every washing
process, at the end of the day, proceeding as
follows:
· Remove the bayonnet safety filter from the
wash pump (L) by twisting it counterclockwise.
· At the end of the day, it is advisable to drain the
dishwasher, fill it with water and have a wash
cycle done on no load, without any racks, in
order to clean the interior of the machine.
· Finally, clean the bottom, walls and interior of
the tank.
· Spray arms must be cleaned periodically. If rin-
sing is deficient, the cause may be an obstruc-
tion of the jets. In this event, dismount the arms
and clean the jets.
· The outside of the machine MUST NOT BE was-
hed under a direct water jet; instead you can
use a wet cloth and any ordinary detergent.
· DO NOT USE any abrasive detergent (etchant,
concentrated lye, etc.) nor any scourer or scra-
per containing normal steel that will cause rust
to develop on the machine.
OTHER IMPORTANT REMARKS
· Before cleaning, servicing or repairing the
machine, it is necessary to unplug it from the
mains.
· When the appliance is going to be inactive for a
long period of time or at night, the door should
be kept open for aeration and avoiding nasty
smell.
· In case of a drain pump failure:
1. Drain the wash tank into a container until
the water level drops below the drain plug.
2. With the drain plug in place, remove the
front bottom panel and change the pump
(this can be done without moving the
machine). In order to drain the machine
manually, connect a drain hose to the
collector. On pulling out the drain plug,
water flows out of the tank by gravity.
· In the event the power supply cable should get
damaged and have to be replaced, the repair
may only be done by a SAMMIC approved assis-
tance service.
· Airborne noise: the emission noise level measu-
red on a typical machine is 71 dB(A) at a distan-
ce of 1m.
· This machine is not designed to be used by
individuals (including children) with reduced
physical, sensorial or mental facilities, or who
lack the relevant experience or knowledge,
unless they are supervised by or have recei-
ved instruction on how to use the apparatus
from a person responsible for their safety.
5
ENGLISH