Important Maintenance Information - AERMEC FCZ Série Manuel D'utilisation Et D'installation

IT EN FR

IMPORTANT MAINTENANCE INFORMATION

WARNING: The fancoil is connected to the power supply and a water
circuit. Operations performed by persons without the required tech-
nical skills can lead to personal injury to the operator or damage to
the unit and surrounding objects.
POWER THE FANCOIL WITH SINGLE-PHASE 230 V ONLY
• Use of other power supplies could cause permanent damage to the
fancoil.
NEVER USE THE FANCOIL FOR APPLICATIONS FOR WHICH IT WAS
NOT DESIGNED
• Do not use the fancoil in husbandry applications (e.g. incubation).
AIR THE ROOM
• Periodically air the room in which the fancoil has been installed; this is
particularly important if the room is occupied by many people, or if gas
appliances or sources of odours are present.
CORRECTLY ADJUST THE TEMPERATURE
• Room temperature should be regulated to ensure maximum comfort to
persons present, particularly in the case of the elderly, infants and invalids.
Prevent temperature fluctuations between indoors and outdoors greater
than 7 °C during summer.
• Note that very low temperatures during summer will lead to greater
electricity consumption.
ORIENT AIR FLOW CORRECTLY
• Air delivered by the fancoil should not be oriented directly at people;
even if air temperature is greater than room temperature, it can cause a
cold sensation and consequently discomfort.
DO NOT USE HOT WATER
• When cleaning the indoor unit, use rags or soft sponges soaked in warm
water (no higher than 40°C).
• Do not use chemical products or solvents to clean any part of the fancoil.
• Do not splash water on interior or exterior surfaces of the fancoil; danger
of short circuit.
PERIODICALLY CLEAN THE FILTER
• Frequent cleaning of the filter will ensure more efficient unit operation.
ATTENTION
In the case of installation in very dusty environments, clean the
dust accumulated in the metal clips inserted into the filter guides
with a vacuum cleaner; perform a visual inspection in order to
verify the contact between clips and filter.
Every anomaly must be communicated to the After-sales Service
(Chapter " Drawings Fig.2).
PACKING
• The units are shipped in cardboard box standard packing and polystirene
shells.
14
DE ES
• Check whether the filter requires cleaning; if it is particularly dirty, clean
it more often.
• Clean the filter frequently. Use a vacuum cleaner to remove built up dust.
Avoid water or detergents if possible since they greatly accelerate loss of
the filter's electrostatic charge.
• After cleaning and drying the filter, fit it on the fancoil by following the
removal procedure in reverse order.
SPECIAL CLEANING
• The removable drip tray and fan volute ensure thorough cleaning of the
unit (by specifically trained personnel), essential for installations in venues
subject to crowding or in those with special hygiene requirements
(Chapter " Drawings" Fig.1).
DURING UNIT OPERATION
• Always leave the filter on the fancoil during operation (otherwise dust in
the air could soil the surface of the coil).
IT IS NORMAL
• During cooling, water vapour may be present in the air delivery of the
fan coil.
• In the heating function it might be possible to hear a slight hiss around
the fan coil. Sometimes the fan coil might give off unpleasant smells due
to the accumulation of dirt in the air of the environment (especially if the
room is not ventilated regularly, clean the filter more often).
• During the operation, there could be noises and creaks inside the device,
due to the various heat expansions of the elements (plastic and metallic),
but this does not indicate any malfunctioning and does not cause
damage to the unit unless the maximum input water temperature is
exceeded.
WARNING
• Avoid that the device is used by children or incompetent persons without
appropriate supervision; also note that the unit should not be used by
children as a game.
ATTENTION
Take out the ambient probe, taking care not to wrench out the
cable connected to the control board. Replace the probe and
connect the cable in the same position (Chapter " Drawings
Fig.3).
&