Using A Pmr446 Transceiver With Cable Connection; Setup And Special Configurations - Midland BT NEXT Guide D'utilisation

Enabling/disabling the wired input
If needed the wired input can be enabled or disabled:
Enabling/Disabling: Make a Long press on the "Forward" and "Middle" button (you
will hear one audio beep tone for enabling confirmation and two audio beep tone
for disabling).
Priority
The BTNext manage the different connection/audio sources based on the fol-
lowing priority rules.
Changing of the operative mode
Every time you change mode (long press of the middle button to toggle between
Intercom/ FM Radio / Phone), the previous audio is closed and the control goes
to the new mode.
Intercom
The Intercom has always a higher priority against the music from the FM Radio or
Phone (including GPS in music play mode). Every time you open the intercom the
music from a Bluetooth source is stopped. Only the audio/Music from the "AUX
wired connection" is always in background by default.
Phone calls
The phone call has always the higher priority and will interrupt every connection,
like music, intercom. Only the AUX wired connection can be still on if the setting
"Wired connection always in background" was enabled.
GPS voice announcement
When the GPS is paired to the "Volume +" button,(high priority) the street voice
announcement will always interrupt the intercom.
When paired using the "Volume -" button, (lower priority) the voice announce-
ment are always in background also if the intercom is active.
AUX wired connection
Music or audio from the AUX wired connection, by default it is always in the
background also when the intercom is open or during a phone call. It is possible
to change this beaver following the procedure described in the "Setup and Special
configuration" chapter.
26 - Midland BT Next
Using a PMR446 transceiver with the cable connection
In order to connect the transceiver to your Midland BTNext, you need to purchase
the specific 2.5mm plug AUX cable, sold separately. Some manufacturers radios
use a different pin configuration, so we recommend that you ask your dealer as to
which cable is best suited to your needs
The cable connected to the transceiver normally has also a PTT button that can be
placed on the handlebar of your bike or held in your hand (If you are the pillion
rider).
To communicate via the attached radio, press the PTT button to speak and release
it to listen. It is not possible to talk and listen simultaneously.
Adjust the volume of the transceiver to your needs, remembering that the volume
adjustment is controlled by the automatic AGC system and that it will therefore
be automatically increased in relation to background noise.
If you wish to use a PMR446 transceiver for group communications and simul-
taneously maintain the Intercom feature enabled between two or more BTNext
devices, you must remember that every time you talk to communicate with the
PMR 446 transceiver (pressing the PTT button), you will also activate the intercom
of the BTNext to the unit connected to the "Middle" button (thanks to the VOX
feature).
To avoid the Intercom activation when you speak on the PMR446, you can decide
to pair the BTNext unit on the "Rear" or "Forward" (where the VOX is not active) or
if you still want to use the "Middle" button, you must disable the VOX feature, as
explained in the previous section.

Setup and special configurations

Resetting all paired devices
Sometimes you may find it necessary to delete all the pairing references stored in
the BTNext unit (reset operation).
To perform this operation you must first enter the setup mode:
› Turn off the unit
› Press and hold down the "Middle" button about 7 sec., until the Red light is
on permanently.
› Than simultaneously press and hold down the "Volume +" and "Volume –"
buttons for 3 seconds. The Blue Light will be lit on for 1 sec and than back
to steady RED.
› Double click on the "Middle" button to exit the "Setup" mode and use the
BTNext.
This procedure deletes all the paired Bluetooth devices stored in the memory and
it is therefore possible to start a new "clean" pairing session.