Clarion DVC920 Mode D'emploi page 4

3. CONTROLS / LES COMMANDES / CONTROLES /
I Control unit /
Module de commande / Unidad de control /
[ VOL ]
[ MUTE ]
SOURCE A-MODE ADJUST
[ DISP ]
[ ENT ]
[ ADJUST ]
[ SOURCE ]
[ A-MODE ]
4. NOMENCLATURE
Names of Buttons
Control Unit [SOURCE] button:
• Switches the input source.
[VOL] button:
[A-MODE] button:
• Raises and lowers the volume.
• Changes the adjustment values in the ADJUST • Adjusts the volume balance in each speaker.
MODE and AUDIO MODE.
[ADJUST] button:
[MUTE] button: • Invokes the ADJUST MODE to set speakers
• Turns off the sound. and other equipment.
[DISP] button: [DSF] button:
• Changes the display. • Changes the sound characteristics in the car.
• Changes set items in the ADJUST MODE.
[POWER] button:
• Turns the power on and off.
[ENT] button:
• Determines the adjustment setting in the AD
JUST MODE.
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
Remarque: Veuillez déplier cette page et vous référer aux schémas quand vous lisez chaque chapitre.
Nota: Cuando lea los capítulos, despliegue esta página y consulte los diagramas.
5
DVC920
280-7804-00_02-08(En) 4
Control Unit Display
DOLBY DIGITAL DOLBY Digital indicator
: Lights when playing Dolby Digital sound from the Digital input connector.
DOLBY PLII (Dolby Pro Logic II) indicator
: Lights when selecting the various Dolby Pro Logic II function modes.
LINEAR PCM LINEAR PCM indicator
: Lights when playing linear PCM sound from the Digital input connector.
DTS DTS indicator
: Lights when playing DTS sound from the Digital input connector.
D S F POWER
D.S.F. D.S.F. indication
[ POWER ]
[ DSF ]
Press the [SOURCE] button on
the control unit to display image
when the input source has been
changed.
DIGITAL1:
When a digital source connected
to a digital input 1 is selected.
DIGITAL2:
When a digital source connected
to a digital input 2 is selected.
ANALOG1:
When an analog source con-
nected to an analog input with
RCA plugs is selected.
ANALOG2:
When an analog source con-
nected to an analog input with a
CeNET cable is selected.
6
DVC920
Title indication
Center speaker indication
Rear (surround)
speaker indication
Subwoofer indication
Mute indication
Front speaker indication
2/22/02, 2:05 PM
5. OPERATIONS
Note: Be sure to read this chapter referring to the front diagrams of
Basic Operations
chapter "3. CONTROLS" on page 5 (unfold).
G ANALOG1 (Analog 1):
CAUTION
Use this setting when playing back an analog
Be sure to lower the volume before switch-
input source connected using RCA plugs.
ing off the unit power or the ignition key. The
G ANALOG2 (Analog 2):
unit remembers its last volume setting. If you
switch the power off with the volume up, when Use this setting when playing back an analog
you switch the power back on, the sudden
input source connected using a CeNET cable.
loud volume may hurt your hearing and dam-
age the unit.
Adjusting the sound volume
Turning on/off the power
The sound volume on a DVD video disc can
Note:
become very loud. For that reason, turn up
• Be careful about using this unit for a long time with-
out running the engine. If you drain the car's battery the sound volume gently when the video im-
too far, you may not be able to start the engine and
age is displayed.
this can reduce the service life of the battery.
Press the [VOL] buttons on the control unit.
1. Press the [POWER] button.
2. The settings are displayed on the control unit
:increases the sound volume.
display.
3. Press the [POWER] button to turn off the
power.
:decreases the sound volume
Switching input source
Note:
Change the settings to suit the input signal
• Adjust the audio volume using the controls on this
source.
control unit. The audio volume cannot be adjusted
• The initial setting is [DIGITAL1].
using the Center Unit controls.
Press the [SOURCE] button.
Changing display settings
Each time the [SOURCE] button is pressed, the
indications change as shown below. Press the [ ] or [
[DIGITAL1] → [DIGITAL2] → [ANALOG1] →
Each time the [
[ANALOG2] → [DIGITAL1]
pressed, the indications change as shown below.
[SS 1] → [SS 2] → [DISP OFF] → [PROGRAM]
• The original mode is resumed when the but-
→ [SS 1]
ton is not pressed during a 7 second inter-
val.
G SS1: displays the dolphin.
Notes:
• Sound may be interrupted for a very short period
while audio format is being distinguished.
• If skip or pause operations are performed on the
G SS2: displays the airplane
DVD player while sound is being played back,
noise may be heard for a brief interval.
G DIGITAL1 (Digital 1):
Use this setting when playing back digital input
G DISP OFF: the display is off.
sources connected using an optical-fiber cable
to digital input 1.
G PROGRAM (Program):
G DIGITAL2 (Digital 2):
Indicates the format of the signals input from
Use this setting when playing back digital input the DIGITAL connectors.
sources connected using an optical-fiber cable
• MONO: Monaural sound
to digital input 2.
• STEREO: Stereo sound
CAUTION
] [DISP] button.
] or [ ] [DISP] button are
7
DVC920
280-7804-00