Numark Total Control MKII Guide D'utilisation Simplifié page 7

7. JOG WHEEL – When the deck is stopped,
the JOG WHEEL will scratch the selected
track. When the deck is playing, the JOG
WHEEL will bend the track's pitch.
8. VOLUME – Adjusts the volume of the
corresponding deck.
9. CROSSFADER – Fades between the two
tracks playing on the virtual decks. If the
crossfader is in the left-most position, you
will only hear the audio from Deck A. If the
crossfader is in the right-most position, you
will only be able to hear the audio from
Deck B. When the crossfader is in a point
between the two, you will hear both Decks.
10. GAIN – Adjusts the gain level of the
corresponding deck.
11. EQ – Use these knobs to adjust the levels
of the Treble, Mid, and Bass frequencies
on each deck. Pressing down on an EQ
knob makes it function like a "kill switch,"
removing that frequency band from the
music on that deck. The LED next to the
knob will illuminate when the Kill feature is
engaged. To disengage it press the knob
again.
12. MASTER – Controls the Master level,
allowing you to change the overall volume
of the mix.
13. PH MIX – Adjusts the balance between the
Monitor and Master channels in the
headphones. Please note that, unless you
are using a multiple output audio interface,
the Monitor and Master Mix channels will
be the same.
14. PH VOL –
headphone mix level.
unless you are using a multiple-output
audio interface, the Monitor and Master Mix
channels will be the same.
15. PFL – Press the PFL button to send the
music playing on the deck to the Monitor
channel. Please note that if you are not
using a multiple-output audio interface, the
Monitor and Master Mix channels will be
the same.
16. PITCH – Changes the pitch or tempo of the
music playing on that deck.
17. FINE PITCH
adjustments to the music on the deck.
18. TAP – Tap this button in time with the
beats of the music on that deck. This will
enter a new BPM ("beats per minute")
reading for that track.
19. KEY – Engages the Master Tempo feature,
which locks the musical key of the track to
the original key (as if it were playing with
0% pitch adjustment). You can then adjust
the tempo of the track without affecting its
key or pitch.
This knob adjusts
Please note that,
– Makes fine
20. SYNC – Synchronizes the music playing
on that deck to the music playing on the
other deck.
21. PITCH BEND -/+ – You can use these
two pitch bend buttons to temporarily
adjust the pitch and tempo of the music
playing on the corresponding deck.
Pitch bend is typically used to make
small adjustments when mixing two
tracks
synchronously.
22. LOOP IN – Press this button to set the
starting point of a loop.
23. LOOP OUT – Press this button (after
pressing LOOP IN) to set the ending
point of a loop. Once you press it, you
will jump back to the Loop In point and
the loop will be active. To turn a loop
off, simply press LOOP OUT again.
24. FX AMT – Adjusts how much of the
selected effect will be heard in the
Master Mix. If the knob is all the way
down, you will hear only the original
("dry") sound. If the knob is all the way
up, you will hear the maximum amount
of effected ("wet") sound.
25. SELECT – Selects an effect to be
applied to the Master Mix.
26. PAR – Adjusts the amount of the
designated Effect Parameter.
note that this parameter will vary
depending on the selected effect.
27. ON / OFF – Press this button to turn the
master effect on and off.
the
28. FILTER AMT – Adjusts the amount of
filter applied to the music on that deck.
The center position is zero. Turning the
knob clockwise will increase the amount
of high-pass filter.
counter-clockwise
amount of low-pass filter.
29. FILTER ON / OFF – Activates or
deactivates the filter on that deck.
pitch
7
so their beats
Turning the knob
will increase
occur
Please
the