Coleman FAST PITCH Mode D'emploi page 9

2. Tear Down/ Delation Instructions
2.1. Open inner tent doors.
2.2. Open double layer entrance mesh doors – keep main entrance doors opened for easier air evacuation when rolling the tent.
2.3. Unpeg guy line and stake points.
2.4. Remove all iberglass pole from their sleeve – Store them in the pole bag.
2.5. To delate the air pole, turn the valve cover anticlockwise. Push the spring loaded pin until it stays down. The valve is now opened
and pole starts to delate. Wait until air poles are completely delated. Note: a loud noise could occur when push the pin – this is
normal.
2.6. Roll and/or fold the tent in the direction of the opened valve to expel as much air as possible out of the air poles.
2.7. Lay the tent lat again.
2.8. Fold the tent and roll it to it the carry bag.
2.9. Store pegs and poles bags into the carry bag.
2.10. Ensure your tent is totally dry before storing to avoid mildew/rotting and metal parts rusting.
3. Care, Storage, Cleaning
3.1. Store your tent in a dry, cool, well ventilated space clean from dirt and debris. Never leave your packed tent in direct sunlight –
choose a dark area.
3.2. Dirty Tents can only be washed using clean water and soft sponge. Never use detergent, soaps, or a brush on your tent – as this
could damage fabrics and drastically reduce the waterproof properties of your tent.
3.3. Never spray insecticides on or in the tent - as this could damage fabrics and drastically reduce the waterproof properties of your tent.
3.4. If the case of tape coming off – this may happen after prolonged exposure to sun and normal ageing of tent – you can repair by
removing the loose part and using a seam sealer (inside) combined with a waterproof spray (outside) to re-seal your seams.
4. Repair/Replace air pole tube
4.1. Delate completely the defective air pole by opening the valve.
4.2. Unzip the main sleeve and take the air pole out of the tent zipped sleeve (Fig. M, N).
4.3. cut the zip-tie used to maintain the zipper sliders of your air pole envelope. (Fig O).
Never unzip the envelope when the air pole is inlated – this could cause the bladder to quickly pop out and explode.
WARNING
4.4. Take the air bladder out from its envelope – Do not completely remove the air bladder – Do not remove/unscrew the valve. Take care
not to damage the air bladder around the valve area by pulling too much. (Fig. P)
4.5. To check the position of the leakage, inlate the air bladder and, using a basin of water, locate the position of the puncture.
Put a really small amount of air in the bladder – the bladder cannot withstand pressure without its envelope. The
WARnInG
overpressure could cause injury as the bladder could explode.
clean the area around the puncture to remove water, grease and dirt.
4.6.
4.7. Apply the provided coleman repair adhesive patch to perfectly cover the puncture. Do NOT cut the repair patch to ensure maximum
repair eficacy – Rub on the bladder until perfectly stuck (Fig. Q).
4.8. Once completely glued (minimum 30 minutes), slide back carefully the bladder into the envelope. close the zip sliders (always take
care not to catch the bladder into the zip sliders) (Fig. R).
4.9. To ensure the repair eficacy, inlate the pole at the recommended pressure and check pressure after some time. Once repair is done,
slightly delate the air pole, re-connect together both zip sliders with a zip-tie (Fig. S).
4.10. Replace the pole into the tent zipped sleeve.
4.11. The repair patches provided into your repair kit are it for small holes (10mm length) - If you are not able to repair (larger puncture,
valve issue ...), you shall replace completely the air pole (bladder and envelope). Spares Poles are available from your coleman
aftersales service.
Warranty Period: 2 Years.
9
GB
®