Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
14
Caution! Make sure that the control panel socket G is facing
up.
Caution! The picture of control panel is for informational
purposes only. The actual product may vary.
G
J
•
Align the mounting plate with the right side of
the control panel. Slide the control panel into the
mounting plate from the left until the control panel
cannot move.
1
2
CABLE TRAY INSTALLATION
•
Align the mounting holes in the tray hooks with the
screw holes in the cable tray.
•
Mount cable hooks to cable tray D with S-D screws
from below using a phillips screwdriver.
•
Hang the cable trays on the traverse and tighten the
knobs on the hooks.
DESKTOP ASSEMBLY
•
Remove the adhesive backing layer from the rubber
pads.
•
Stick the pad to the traverse surface in 8 places as
shown.
EN
S-F
S-F
•
Align the previously drilled screw holes with the
mounting holes on the traverse. Fasten with S-B
screws from below.
•
Repeat the same steps to mount the other side of
the countertop.
S-B
•
Fasten the control panel to the counter with S-B
screws and a drill.
•
Stick the adhesive clip to the S-E cable under the
desk to organize the cables.
1
S-C
2
S-E
FOOT ADJUSTMENT
•
There are two adjustable pads under each foot. To
ensure stability, the desk should be adjusted by
rotating the pad.
Tip: Use the bubble level to check the desk level.
EN
•
Connect the device to the power supply.
3.3. DEVICE USE
Digital control panel for electric desk height adjustment.
WORKING WITH THE DEVICE
•
Height adjustment - up/down button - press and
hold the button to raise/lower the desk
•
Timer - used to inform the user about getting up
after a specified time. To set the time, press the „T"
button. Each time you press the „T" button, the time
increases by another 30 minutes. The maximum time
setting is 2 hours. When the display stops flashing,
the time has been set successfully and the indicator
light in the upper right corner of the panel lights up.
When the time is up, a beep will sound to remind
you. The clock will automatically turn off after a long
beep. To cancel the countdown, press the „T" button
5 times until the current altitude appears on the
display and the control lamp goes out.
•
Memory - set the desk in the desired position; Press
the „M" button and then the „S" will appear on the
display. Then press the „1", „2" or „3" button to code
the height setting. You can save up to 3 heights in
the device's memory.
•
Power saving mode - if no operations are performed
for 10 minutes, the system will go into power saving
mode. To return to normal operation, unplug the
power cord and then plug it in again.
•
Measuring switch [cm inches] – press and hold the
„T" button for 8 seconds. A beep will announce the
unit change from centimeters to inches. If you want
to change the measuring unit again, hold the „T"
button for 8 seconds.
•
Reset mode - after reconnecting the system, press
the down button until „RST" appears. Hold the
button. The desk will move down and then slightly
rise (make sure that the button was pressed
throughout the reset process). After stopping the
movement, the system is restored to its starting
position.
•
Protective standby mode - After one minute of
inactivity, the device will enter standby mode. To exit
this mode, hold the M button for 3 seconds.
NOTE: The user can manually enter the standby
mode if she/he does not intend to use the panel
- hold down the M button for 3 seconds while the
panel is in normal operation mode.
15
Problem solving:
If the message ER1 / ER2 / HOT / ER3 / ER4 / ER5 appears
on the control panel, you should not worry. This means
that the system has exceeded its rated values by use. To
solve the problem, follow the steps below. If the problems
are not resolved, please contact the place of purchase for
further repair.
ER1:
Step 1: Check if the desk has been overloaded.
If so, immediately remove components from the
countertop and disconnect the power supply. If not,
just disconnect the power supply.
Step 2: Wait 10 seconds and then connect the power
cord.
ER2:
Step 1: The system has reached too high temperature.
Leave the desk to cool for at least 20 minutes.
Caution! Never disconnect power during the cooling
process.
ER3/ER4/ER5:
Step 1: The system has electrical problems. Unplug
the power cord immediately.
Step 2: Wait 10 seconds and then connect the power
cord.
Step 3: Apply „reset mode".
3.4. CLEANING AND MAINTENANCE
a)
Use only non-corrosive cleaners to clean the surface.
b)
After cleaning the device, all parts should be dried
completely before using it again.
c)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
d)
Do not spray the device with a water jet or submerge
it in water.
e)
The device must be regularly inspected to check its
technical efficiency and spot any damage.
f)
Use a soft cloth for cleaning.
g)
Use a soft, damp cloth for cleaning.
h)
Do not use sharp and/or metal objects for cleaning
(e.g. a wire brush or a metal spatula) because they
may damage the surface material of the appliance.
Publicité
Table des Matières
