Preparing For Use - Fromm & Starck STAR ATFE 03 Manuel D'utilisation

12
A. Timer
B. Memory/screen lock (unlock)
C. Move down
D. Move up
E. Memory 1/2/3
F. Display
G. Signal lamp
Electric sit stand desk frame
3 4
2
5 6
8 7 5
1
1. Foot
2. Side bracket
3. Traverse
4. Hook
5. Control box
6. Cable management tray
7. Control panel
8. Lifting column

3.2. PREPARING FOR USE

Electric sit stand desk frame
ELEMENTS LIST:
A(X1) B(X2) C(X2) D(X1)
E(X2) F(X1) G(X1) H(X2)
I(X1) J(X1)
A. Traverse
B. Side bracket
C. Foot
D. Cable tray
E. Lifting column
F. Mounting plate
G. Control box
H. Hook
I. Power plug
J. Control panel
CONNECTION ELEMENTS
S-A(x20) S-B(x10) S-C(x2)
S-D(x6) S-E(x3) S-F(x8)
S-G(x1)
EN
S-A. Hexagon head screw
S-B. Phillips head screw + 1 spacer pad
S-C. Long phillips head screw
S-D. Short phillips head screw
S-E. Cable clip
S-F. Rubber pad
S-G. Allen wrench
Warning! Before assembling the device, make
sure that the number of items in the packaging
corresponds to the list of items contained in this
manual.
The temperature of environment must not be higher than
2
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device is
being used. There should be at least 10 cm distance between
each side of the device and the wall or other objects. Position
8
the device such that you always have access to the power
plug. The power cord connected to the appliance must be
properly grounded and correspond to the technical details on
the product label.
ASSEMBLING THE DEVICE
1
Before installation, prepare and secure the appropriate space.
It is recommended to use a protective mat or pad to prevent
product / floor scratches.
FASTENING SIDE BRACKETS
• Unpack the traverse A and carefully place it on the
floor. Fasten bracket B to the end of the traverse
A and fasten with S-A screws using the S-G allen
wrench. Repeat the same steps for the other side of
the traverse.
A
S-A
S-G
B
CAUTION! The figures of traverse brackets and side
brackets are placed on the front of the co mponents. Make
sure that the traverse and side brackets are faced up when
mounting as this position is more comfortable to make
following steps.
DRILLING MOUNTING HOLES
• Loose the screws S-G which mount adjustable
connector, but do not remove them.
S-G
• Place the mounted frame at the back of the table
counter.
• Make sure that the frame is placed in the centre of
the table.
• Fit the frame to the size of the benchtop.
EN
S-G
• Retighten all S-G screws to complete the adjustment
CAUTION! Mounting holes should be greater than 10 mm
and diameter less than 3 mm.
INSTALLATION OF THE LIFTING COLUMNS
• Remove the desk counter for further installation
• Insert two lifting columns (one on each side) into the
traverse with the lifting columns faced inward. Make
sure that the mounting holes in the lifting columns
are completely aligned with the screw holes in the
traverse.
• Fasten the lifting column E and the side bracket with
S-A screws and S-G allen wrench.
E
S-G
S-A
FOOT INSTALLATION
• Place the foot C on the bottom of the lifting column.
Make sure that the mounting holes on the foot are
completely aligned with the screw holes in the lifting
column E.
• Fasten the foot C with S-A screws and S-F allen
wrench.
13
S-G
S-A
C
MOUNTING PLATE INSTALLATION
• Align the mounting holes on the mounting plate
with the screw holes, as shown.
• Fasten the mounting plate F in the middle of the
traverse with S-D screws and a phillips screw.
• Caution! The arrow on the mounting plate indicates
the direction of movement in the control box. Follow
the direction of the arrow to mount the control box
in the next step.
S-D
F
• The mounting plate can be mounted on the right
and left.
CONNECTING CABLES AND MOUNTING THE CONTROL
PANEL
• Turn the desk frame upwards.
• Connect the two motor cables to the two ports
marked „M1" and „M2"
• Connect the control panel cable to the port marked
„P2"
• Insert the power plug I into the port on the left.
M1&M2
P2
AC
I