Technical Data; Preparations For Use - Roller Pulsar Notice D'utilisation

eng

1. Technical Data

Use for the intended purpose
WARNING WARNING
Only use ROLLER'S Pulsar for the intended purpose of soft soldering of copper
pipes. All other uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
ROLLER'S Pulsar:
Electric soldering device, 2 prism electrodes, operating instructions.
ROLLER'S Pulsar Super-Pack:
Electric soldering device, 4 prism electrodes, 2 rod electrodes, pipe cutter
ROLLER'S Corso Cu-INOX 3–35, pack of 10 ROLLER'S Cu cloth, operating
instructions, steel case.
1.2. Article numbers
ROLLER'S Pulsar, Electric soldering unit
ROLLER'S Pulsar Super-Pack
Prism electrode with holder, pack of 2
Prism electrode, pack of 2
Rod electrode, pack of 2
ROLLER'S Cu cloth, pack of 10
Steel case with inlay
Machine cleaner
1.3. Working range
Soft soldering of hard and soft copper piping Ø 6 – 54 mm
Heating capacity
1.4. Electrical data
Rated voltage (mains voltage)
Rated power input
Rated frequency
Rated current
Protection class
Control voltage
Secondary no-load voltage
Secondary rated voltage
Secondary rated current
Shutoff operation AB
Protection class
Secondary overload protection by temperature switch
1.5. Dimensions
Length × width × height
1.6. Weights
Unit
1.7. Noise Information 7. Noise Information 7
Emission at workplace
1.8. Vibrations
Weighted effective value of acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
Attention: The indicated weighted effective value of acceleration can differ
during operation from the indicated value, dependent on the manner in which
the device is used. Dependent upon the actual conditions of use (periodic duty)
it may be necessary to establish safety precautions for the protection of the
operator.

2. Preparations for use

2.1. Electrical connection
WARNING WARNING
Caution: Mains voltage present! Before connecting the ROLLER'S Pulsar, Caution: Mains voltage present! Caution: Mains voltage present! Before connecting the ROLLER'S Pulsar,
check whether the voltage given on the rating plate corresponds to the mains
voltage. Only connect the electric soldering device of protection class I to a
socket/extension lead with a functioning protective contact. On building sites,
in a wet environment, indoors and outdoors or under similar installation condi-
tions, only operate the electric soldering device on the mains with a fault current
protection switch (RCD) which interrupts the power supply as soon as the
leakage current to earth exceeds 30 mA for 200 ms.
NOTICE NOTICE
ROLLER'S Pulsar is not suitable for outdoor use.
164011
164050
164110
164111
164115
160300
164250
140119
Ø ¼ – 2⅛"
900°C
230 V~ 110 V~
2000 W 2000 W
50 – 60 Hz 50 – 60 Hz
8,7 A 18,2 A
I
24 V~
7 V~
7 V~
250 A~ 250 A~
S3 15% S3 15%
(AB 0.5 / 3 min) (AB 0.5 / 3 min)
IP 34
210 × 150 × 140 mm
12.9 kg
70 dB (A)
2,5 m/s²
2.2. Selecting the electrodes
As a rule, the prisma electrodes (1), are used, since they have a larger area of
contact with the pipe and hence heat up the latter faster than the rod electrodes
(2). The rod electrodes are intended for cramped spots where operation with
the prisma electrodes is not possible.
NOTICE NOTICE
Check the cylinder head screw (7) regularly for tight fi t and tighten if necessary.
3. Operation
3.1. Mode of operation
When applying the electrodes of the soldering device to a metal conductor, e.g.
A copper pipe, a circuit with low voltage and high current is closed by pressing
the safety switch (3). The electrodes have a relatively high resistance in the
transformer/cable/electrodes/work piece circuit, and therefore heat up. They
may become red hot with larger pipe sizes. The resultant heat is transmitted
to the workpiece by heat conduction, and the workpiece is heated to soldering
tempera ture in a matter of seconds.
3.2. Operating sequence
Prepare the soldering joint properly (see also 3.3). Attach the tongs (4) with
the prisma electrodes (1) or – in narrow spots – with the rod electrodes (2) to
the workpiece. Press the safety switch (3). Keep the safety switch (3) pressed
during the soldering process. The soldering temperature is reached after a few
seconds. Add solder until the solder gap is fi lled. Release the safety switch (3),
detach the tongs from the workpiece. If the workpiece is not fi xed exactly, the
workpiece can be held in the tongs with the safety switch (3) open until the
solder has solidifi ed. Do not move ROLLER'S Pulsar during the soldering
process.
3.3. Soldering material
Use soft soldering wire suitable for soft soldering. Copper pipes and fi ttings
must be bare metal. To prepare the soldering point, apply soft soldering paste
to the pipe piece. Soft soldering pastes contain soldering powder and fl ux. The
advantage of the paste is that the temperature necessary for soldering can be
recognised by the coloured frame of the heated paste and that a better fi lling
I
of the solder gap is achieved. However, soft soldering wire must be added in
24 V~
any case. Only use soft soldering wire and soft soldering paste which comply
7 V~
with the DVGW work sheets GW 2 and GW 7 as well as the corresponding DIN
7 V~
norms. Only use DVGW-tested soft soldering pastes. Observe the national
regulations.
4. Servicing
IP 34
Notwithstanding the maintenance described below, it is recommended to send
in the ROLLER'S Pulsar to an authorised ROLLER contract customer service
workshop for inspection and periodic testing of electrical devices at least once
a year. In Germany, such periodic testing of electrical devices should be
performed in accordance with DIN VDE 0701-0702 and also prescribed for
mobile electrical equipment according to the accident prevention rules DGUV,
regulation 3 "Electrical Systems and Equipment". In addition, the respective
national safety provisions, rules and regulations valid for the application site
must be considered and observed.
4.1. Maintenance
WARNING WARNING
Pull out the mains plug before maintenance work!
Clean the ROLLER'S Pulsar regularly especially when it has not been in use
for a long time. Keep the electrodes free from solder and fl ux. These impair the
heat transfer. Check the correct fi t of the cylinder screws (7) regularly and
tighten if necessary. Check the electrodes (1, 2) and holder (6) for damages
and carbonisation from time to time. Replace the electrodes if necessary. To
replace the prism electrodes, loosen the two screws (5), remove the worn
electrodes, clean the contact faces of the holder with a wire brush, insert new
prism electrodes and re-tighten the screws. Replace deformed or burnt holders.
Clean plastic parts (e.g. housing) only with machine cleaner (Art. No. 140119)
or a mild soap and a damp cloth. Do not use household cleaners. These often
contain chemicals which can damage the plastic parts. Never use petrol,
turpentine, thinner or similar products for cleaning.
Make sure that fl uids can never get onto or inside the ROLLER'S Pulsar. Never
immerse ROLLER'S Pulsar in liquid.
4.2. lnspection/servicing
WARNING WARNING
Pull out the mains plug before maintenance and repair work! This work
may only be performed by qualifi ed personnel.
eng
! ! This work
7