Table des Matières
Publicité
FAMILIARISEZ-VOUS AVEC STATION DE VAPEUR
1.
Bouchon de remplissage de la
bouilloire
2.
Plaque de repos du fer
3.
Cordon d'alimentation
4.
Témoin de vapeur
5.
Témoin d'alimentation
6.
Contrôle de vapeur variable
7.
Tuyau de vapeur
Fiche technique
Tension :
120 V, 60 Hz
Intensité :
1700 watts
Capacité :
27 onces (US) (800 ml)
8.
Bouton d'alimentation On/Off
9.
Bouton de relâche de la
vapeur
10. Poignée
11. Témoin de température
12. Contrôle de température
13. Plaque
14. Godet de remplissage (non
illustré)
24
OPERATING INSTRUCTIONS
This appliance is for HOUSEHOLD USE
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
Before First Use
Remove any labels, stickers or tags
which may be attached to the body or
the soleplate of the iron before using
the steam generator.
WARNING:
Never leave the unit
unattended while plugged in. Always
turn the steam generator "OFF" and
remove the power cord from the
electrical outlet.
WARNING:
The steam generator
must always be turned "OFF" and
disconnected from the electrical
outlet before any cleaning or
maintenance; before filling and
emptying the water tank.
Filling Steam Generator Water
Tank
1. Place steam generator unit on a solid
flat surface.
2. Push the cap down and unscrew the
boiler filler cap.
3. When filling the steam generator
water tank, always use the filling
flask to fill your unit. NEVER fill the
appliance under a tap. Fill the water
tank with 27 US. fl. oz. (800 ml) of
tap water if the water in your area is
not hard water. If it is, then we
strongly recommend using 100%
distilled water. Be careful not to over
fill the water tank. Adding too much
water will cause overfilling and will
result in water drops in the steam.
(Fig. 1)
Fig. 1
4. When finished filling, replace the
boiler filling cap, push cap down and
screw on tightly.
5. Plug the power cord into an electrical
outlet.
Note: The power light will illuminate when
the unit is plugged in, however you must
turn the "On/Off" switch "On" for steam
pressure to build.
6. Press the On/Off switch on the steam
generator to the "ON" position.
7. Turn the temperature control dial on
the iron to the desired temperature
setting.
8. Turn the variable steam control knob
to the desired steam setting.
Using the Iron With Steam
1. Press the On/Off switch on the
generator to the "ON" position.
2. Select the desired amount of steam on
the variable steam control knob. The
steam ready light will illuminate when
the steam is ready. It will take
approximately 9 minutes to heat up a
full tank of water. The steam ready
light will cycle on and off while the
steam generator is in use. (Fig. 2)
Steam Ready
Light
Power Light
Fig. 2
3. Set the temperature control dial on the
iron to the desired temperature.
Note: For ironing with steam, make sure
that the temperature on the temperature
control dial on the iron is set within the
area designated for use with steam, i.e.
between wool (
) and linen
(Max
). When the chosen
temperature is attained, the temperature
ready light will go "Off" and your steam
generator iron is
Press down
for Steam
ready to be used.
4. For steam, press
the steam
release button
down and
hold while
steam is
required.
(Fig. 3)
Fig. 3
WARNING
: Never direct the steam
from the iron at yourself or another
person. Special care must be taken
when the iron is used in a vertical
position. The steam is very hot and
can cause burns.
5
Publicité
Table des Matières
