Special Safety Instructions - Metabo KHE 2660 Quick Mode D'emploi

be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition that
may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
2.5 Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

3. Special Safety Instructions

Wear ear protectors. Exposure to noise can cause
hearing loss.
Use auxiliary handle, if supplied with the tool.
Loss of control can cause personal injury.
Hold power tools by insulated gripping
surfaces, when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool „live" and could give the operator an electric
shock.
Always work with the additional handle correctly
installed.
Always hold the machine with both hands at the
intended handles, take a secure stance and
concentrate on the work.
Always wear protective goggles, gloves, and sturdy
shoes when working with this tool.
Ensure that the spot where you wish to work is free
of power cables, gas lines or water pipes (e.g.
using a metal detector).
If the safety coupling responds, switch off the
machine immediately.
Do not touch the rotating tool!
Secure the workpiece to prevent slipping or rotation
(e.g. by securing with screw clamps).
Remove chips and similar material only with the
machine at a standstill.
Caution must be exercised when driving screws into
hard materials (driving screws with metric or
imperial threads into steel)! The screw head may
break or a high reverse torque may build up on the
handle.
Pull the plug out of the socket before making any
adjustments, changing tools, carrying out
maintenance or cleaning.
Avoid inadvertent starts by always unlocking the
switch when the plug is removed from the mains
socket or whenever the power fails.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
Safety clutch: f the tool jams or catches, the power
supply to the motor is restricted. Due to the strong
force which can arise, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Additional Warnings:
Some dust created by power
WARNING
sanding, sawing, grinding,
drilling, and other construction activities
contains chemicals known to cause cancer,
birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and
other masonry products, and
• Arsenic and chromium from chemicallytreated
lumber.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic
particles.
SYMBOLS ON THE TOOL:
...... Class II Construction
V .......... volts
A .......... amperes
Hz ........ hertz
W ......... watts
BPM..... beat per minute
~
.......... alternating current
n ......... no-load speed
0
rpm ...... revolutions per minute
.../min... revolutions per minute
4. Overview
See page 2.
1 SDS chuck
2 Tool lock
3 Chuck lock
ENGLISH en
California Prop 65 08_2018
5