Publicité
Les langues disponibles
Les langues disponibles
x
AIRPRO 120
®
12 VOLT CORDED COMPRESSOR WITH DIGITAL GAUGE
INSTRUCTION MANUAL
2
1
4
5
7
6
9
10 11 12
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
All Rights Reserved © 2018 Baccus Global LLC, Boca Raton, FL 33432
1-877-571-2391
This Class B digital apparatus complies with Canadian ICES-003.
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided,
may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should always be
followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or
equipment could result in serious injury and property damage. There are certain applications for which tools and
equipment are designed. Manufacturer strongly recommends that this product NOT be modified and/or used for
any application other than for which it was designed. Read and understand all warnings and operating instructions
before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating the air compressor. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
• This product is intended for household, consumer use only.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS
OR PROPERTY:
• Avoid dangerous environments. Don't use this unit in damp or wet locations. Never submerge this unit in water;
do not expose it to rain or snow, or use when wet.
• Keep children away. All visitors should be kept at a distance from work area.
• Store idle unit indoors. When not in use, this unit should be stored indoors in a dry, and high or locked-up place
– out of the reach of children.
• Disconnect the unit. Disconnect the unit from the power supply when not in use.
• Use of accessories and attachments. The use of any accessory or attachment not recommended for use with this
unit could be hazardous. Refer to the accessory section of this manual for further details.
• Stay alert. Use common sense. Do not operate this unit when you are tired or impaired.
• Check for damaged parts. Any part that is damaged should be replaced by the manufacturer before further use.
Contact the manufacturer at (877) 571-2391 for more information.
• Do not operate this unit near flammable liquids or in gaseous or explosive atmospheres. Motors in these tools
normally spark, and the sparks might ignite fumes.
• Never cover unit while it is operating.
• Disconnect the unit from any power source before attempting maintenance or cleaning.
SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS
WARNING – BURST HAZARD:
• Carefully follow instructions on articles to be inflated. Never exceed recommended pressures. Bursting articles
can cause serious injury.
• Always monitor the pressure on the LCD screen.
CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• NEVER connect this unit to a positive grounded vehicle.
• The 12V DC Accessory Plug must only be connected to batteries with a nominal output voltage of 12 volts. The
unit will not operate from a 6 volt battery and will sustain permanent damage if connected to a 24 volt battery.
• Never leave the compressor unattended while in use.
• When using a vehicle's 12V DC accessory outlet as a power source, be aware that some vehicles require the
ignition be turned on to power the accessory outlet. Manufacturer strongly recommends that you leave the
ignition of the vehicle turned on (NOT in the accessory position) while operating the compressor to avoid
draining the vehicle battery.
• The Air Compressor is capable of inflating to 120 pounds per square inch (PSI) pressure. Follow the instructions in
the "Portable Compressor" section.
• When not in use, always turn off the compressor and disconnect the 12V DC Accessory Plug from the accessory
outlet of your vehicle or other DC power source.
• To prevent hose damage, secure the Compressor Hose and Sure Fit
®
• Always allow the unit to cool before storing it.
SAVE THESE INSTRUCTIONS
INTRODUCTION
CDC120SCA
Congratulations on purchasing your new Stanley
Gauge. Read this Instruction Manual and follow the instructions carefully before using this unit.
FEATURES
1. LED Area Light
2. Nozzle Adapter Storage Compartment
3. Storage Clips (2 in total)
4. Compressor Trigger
5. Air Hose and Sure Fit
6. 12V DC Accessory Plug
INSTALLING THE AIR HOSE STORAGE CLIPS
3
Position each of the (2) Air Hose Storage Clips against one of the slots on the right side of the unit; then simply
snap them into the top slot and bottom slot respectively (as shown).
8
PORTABLE COMPRESSOR
This 12 Volt DC Air Compressor is the designed for use with vehicle tires, trailer tires and recreational inflatables.
The compressor hose with tire fitting is stored on the storage clips at the side of unit. A Nozzle Adapter is
supplied and is stored in the Nozzle Adapter Storage Compartment. Refer to the "Features" section to locate all
components.
The 12V DC Air Compressor can be used in either Auto Mode or Manual Mode, as detailed in the following sections.
IMPORTANT: When the compressor is operated either in the Manual Mode or at a low PSI in the Auto Mode, the
unit may start in low and gradually rev up. When the compressor is operated at higher PSIs in Auto Mode, the unit
may operate normally for several minutes, then rev down for a few minutes before returning to normal operation.
This feature protects the unit from overheating during normal use. In any event, do not operate the compressor
continuously for extended periods of time (approximately 10 minutes, depending on ambient temperatures), as it
may overheat. This could damage the compressor. If the compressor must be operated for longer periods: every 10
minutes press and hold the Power Button for one second to turn the compressor off, then restart after a cooling
down period of approximately 30 minutes.
Note:
The LED Area Light will remain lit as long as the unit is turned on.
Inflating Tires or Products with Valve Stems in Auto Mode
In the Auto Mode, the desired pressure value can be preset and stored in the unit's memory and the compressor
will automatically stop once this preset pressure is reached. The Power Button turns the unit on and off. The
Increase Pressure Control Button (+) and Decrease Pressure Control Button (–) are used to select a pressure value for
when the compressor is used in Auto Mode. All three buttons are located on the control panel on the back of the
unit (refer to the "Features" section to locate).
1. Connect the unit's 12V DC Accessory Plug to a vehicle's accessory outlet or other 12 volt DC power source.
Rotate the plug slightly to make sure there is good contact. Position the unit to allow adequate space for
proper ventilation of the compressor.
2. Screw the Sure Fit
3. Press the Power Button to turn the unit on. The digital display will alternately show the flashing pre-set PSI
value (that was last set by the Pressure Control Buttons) for 2 seconds; then it will flash the current pressure of
the item being inflated for 5 seconds. The display will then light solid.
4. Press the Increase (+) and Decrease (–) Pressure Control Buttons to select the desired pressure from a range pre-
set values (between 3 and 120), which will display on the backlit LCD screen. Hold the Button to scroll upward
or downward more quickly. Once the desired pressure has been reached, release the Button and wait two
seconds. The digital display will flash the new selected pressure. This pressure value is now stored in the unit's
memory until it is manually reset.
5. Press the Power Button once more to begin inflation. The digital display will only show the current pressure of
the object (which will light solid) to indicate that the compressor is working. Monitor the pressure on the LCD
screen.
6. When desired pre-set pressure is reached, the compressor will stop automatically. Press and hold the Power
Button for one second to turn off the unit.
7. Unscrew and remove the Sure Fit
8. Disconnect the unit's 12V DC Accessory Plug from the vehicle's accessory outlet or other 12 volt DC power source.
Store the plug inside the storage compartment at the base of unit.
IMPORTANT AUTO MODE OPERATING NOTES:
• To interrupt the inflation process, press the Power Button once. To resume the inflation process, press the Power
Button again.
• To switch to Manual Mode, press the Power Button once to stop the inflation process, then press the Compressor
Trigger. (The unit cannot switch to the Manual Mode while it is inflating.)
• To shut down the unit at any time, press and hold the Power Button for one second.
• To select a new pressure value, press the Power Button once, then press the Increase (+) or Decrease (–) Pressure
Control Buttons and resume the inflation process at step 5.
Inflating Tires or Products With Valve Stems in Manual Mode
In the Manual mode, the Compressor Trigger on the front of the unit is used to operate the compressor until the
desired pressure value is reached.
1. Connect the unit's 12V DC Accessory Plug to a vehicle's accessory outlet or other 12 volt DC power source.
Rotate the plug slightly to make sure there is good contact. Position the unit to allow adequate space for
proper ventilation of the compressor.
2. Screw the Sure Fit
3. Press the Power Button to turn the unit on. The digital display will alternately show the flashing pre-set PSI
value (that was last set by the Pressure Control Buttons) for 2 seconds; then it will flash the current pressure of
the item being inflated for 5 seconds (which will then light solid).
4. Press the Compressor Trigger to begin the inflation process. The digital display will only show the current
pressure of the object which will light solid to indicate that the compressor is working. Monitor the pressure on
the LCD screen.
5. When the desired pressure is reached, release off the Compressor Trigger and the compressor will stop. Press
and hold the Power Button for one second to turn off the unit.
6. Unscrew and remove the Sure Fit
7. Disconnect the unit's 12V DC accessory plug from the vehicle's accessory outlet or other 12 volt DC power
source. Store the plug inside the storage compartment at the base of unit.
IMPORTANT MANUAL MODE OPERATING NOTES:
• To interrupt the inflation process, release the Compressor Trigger. To resume the inflation process, press the
Compressor Trigger again.
nozzle using the Storage Clips after each use.
• To switch to Auto Mode, release the Compressor Trigger, then press the Increase (+) or Decrease (–) Pressure
Control Buttons or the Power Button. (The unit cannot switch to the Auto Mode while it is inflating.)
• To shut down the unit at any time, press and hold the Power Button for one second.
AIRPRO 120
Corded Digital Air Compressor with Digital
®
®
7. 12V DC Accessory Plug Storage Compartment
8. Digital Display (PSI Pressure Value)
9. Nozzle Adapter
10. Decrease Pressure Control Button (–)
Nozzle
11. Power Button
®
12. Increase Pressure Control Button (+)
UPPER SLOT
AIR HOSE
STORAGE CLIPS
(2 IN TOTAL)
LOWER SLOT
nozzle onto the valve stem. Do not overtighten.
®
nozzle from the valve stem.
®
nozzle onto the valve stem. Do not overtighten.
®
nozzle from the valve stem.
®
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of the nozzle adapter.
1. Connect the unit's 12V DC Accessory Plug to a vehicle's accessory outlet or other 12 volt DC power source.
Rotate the plug slightly to make sure there is good contact. Position the unit to allow adequate space for
proper ventilation of the compressor.
2. Screw the nozzle adapter into the Sure Fit
nozzle. Do not overtighten.
®
3. Insert the nozzle adapter into item to be inflated.
4. Press the Power Button to turn the unit on. The digital display will alternately show the flashing pre-set PSI
value (that was last set by the Pressure Control Buttons) for 2 seconds; then it will flash the current pressure of
the item being inflated for 5 seconds (which will then light solid).
5. Follow either steps 4 through 6 in the "Inflating Tires or Products With Valve Stems at Auto Mode" section or
steps 4 through 5 in the "Inflating Tires or Products With Valve Stems at Manual Mode" section.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
6. Disconnect the nozzle adapter from the inflated item.
7. Unscrew and remove the nozzle adapter from the Sure Fit
nozzle.
®
8. Disconnect the unit's 12V DC Accessory Plug from the vehicle's accessory outlet or other 12 volt DC power source.
Store the plug inside the storage compartment at the base of unit.
USING THE LED AREA LIGHT
The Area Light is controlled by the Compressor. When the Compressor is turned on, the Area Light is activated.
When the Compressor is tuned off, the Area Light turns off. Press the Power Button (refer to the "Features"
section to locate) to turn the Compressor and Area Light on. Press the Power Button and hold for one second to
turn the unit off. Make sure the Power Button is turned off when the unit is being stored.
CARE AND MAINTENANCE
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth
moistened with a mild solution of water and detergent. Except for the fuse in the 12V DC Accessory Plug, there
are no user-replaceable parts.
Fuse Replacement (in Vehicle Accessory Plug)
1. Unscrew the end cap of the plug (counterclockwise).
2. Remove the fuse and check it with a continuity checker to see
if it is good or blown.
3. Replace with a new 15 amp fuse, if needed.
4. Carefully reassemble (turning clockwise). DO NOT OVERTIGHTEN.
5. Test for proper operation of the unit.
TROUBLESHOOTING
Air Compressor will not turn on
• Make sure the Power Button is pressed to turn the unit on and that all directions in the "Portable Compressor"
section have been followed exactly.
• Make sure the 12V DC Accessory Plug is properly connected to a functioning DC power source. Rotate the plug
slightly to make sure there is good contact.
• The fuse in the 12V DC Accessory Plug may be blown.
Air Compressor will not inflate
• Make sure the Power Button is pressed to turn the unit on and that all directions in the "Portable Compressor"
section have been followed exactly.
• Make sure the nozzle is securely screwed on to the valve stem when attempting to inflate tires; or that the
nozzle adapter is securely screwed into the Sure Fit
nozzle and is inserted properly into the item to be inflated
®
on all other inflatables.
LED Area Light does not come on
• Make sure the Power Button has been pressed to turn the unit on (when the Compressor is turned on, the Area
Light turns on).
If the unit does not operate after taking the steps given above, contact the manufacturer at (877) 571-2391.
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you need assistance
regarding accessories, please contact the manufacturer at (877) 571-2391.
WARNING: The use of any accessory not recommended for use with this appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the manufacturer at
(877) 571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of ONE (1) YEAR from
the date of retail purchase by the original end-user purchaser ("Warranty Period").
If there is a defect and a valid claim is received within the Warranty Period, the defective product can be replaced or
repaired in the following ways: (1) Return the product to the manufacturer for repair or replacement at manufacturer's
option. Proof of purchase may be required by manufacturer. (2) Return the product to the retailer where product was
purchased for an exchange (provided that the store is a participating retailer). Returns to retailer should be made within
the time period of the retailer's return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase
may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time
set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal wear and tear,
accidents; damages sustained during shipping; alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to
follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other rights which vary from
state to state or province to province. This product is not intended for commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the product to:
Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432. Baccus Global LLC, toll-free
number: (877) 571-2391.
SPECIFICATIONS
Input:
12V DC
LED Area Light:
1 white LED
Compressor:
120 PSI maximum
12V DC Acccessory
Plug Fuse:
15A
Sure Fit
and AIRPRO
are registered U.S. trademarks owned by Baccus Global, LLC.
®
®
Imported by Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
RD122718
Publicité
