Pip (Picture-In-Picture) And Pap (Picture-And-Picture) Modes; Picture Mode Selection; Freezing Picture; Zoom Modes - TECHWOOD TL3210TN875 Mode D'emploi

PIP (Picture-in-Picture) and
PAP (Picture-and-Picture)
Modes
Press the " " button to switch to PIP mode.
At PIP Mode, a small picture (PIP picture) is displayed
on the main picture. There are 1 size and 4 positions
(upper left, upper right, bottom left and bottom right)
available for the PIP window. You can use the "
" button to change the PIP position. Aspect Ratio
of the PIP window is fi xed and 4:3.
When PIP Mode is entered, the default active window
is the PIP window and the active window is indicated
by a red frame around it. The active window can be
changed by pressing the " " or " " buttons. The
status info OSD belongs to active window. The place
of the status OSDs are same for both windows.
Press the " " button again to exit the PIP mode.
Press the " " button to switch to PAP mode.
At PAP Mode, two pictures with equal sizes are
displayed on the screen. Aspect Ratios of the windows
are fi xed.
When you switch to PAP Mode, main window in PIP
Mode will be displayed on the right side of the screen.
The active window can be changed by pressing the
" " or " " buttons.
Press the " " button again to exit the PAP mode.

Picture Mode Selection

By pressing PP button, you can change Picture
Mode settings in accordance with your viewing
requirements. Available options are Dynamic, Natural,
Cinema and Pixellence (optional).
Note : This function will not be available while in PC mode.

Freezing Picture

You can freeze the picture on the screen by pressing
the " OK " button on the remote control in TV mode.
Press the " OK " button to freeze picture. Press again
to quit freeze mode.

Zoom Modes

You can change the aspect ratio (image size) of the TV
for viewing the picture in different zoom modes.
Press "WIDE" button to directly change the zoom
mode.
Available zoom modes are listed below.
Note:
In YPbPr and HDMI modes, while in 720p-1080i resolutions,
only 16:9 mode is available.
In PC mode, only 16:9 mode is available.
01-[GB]_MB36_MASQUE_HDIDTV-MPEG4_BRONZE8_32875W_1059UK_10067832_50165295.indd 28 01-[GB]_MB36_MASQUE_HDIDTV-MPEG4_BRONZE8_32875W_1059UK_10067832_50165295.indd 28

Auto

When a WSS (Wide Screen Signalling) signal, which
shows the aspect ratio of the picture, is included in
the broadcast signal or the signal from an external
device, the TV automatically changes the ZOOM
mode according to the WSS signal.
• When the AUTO mode does not function correctly
due to poor WSS signal quality or when you want to
change the ZOOM mode, change to another ZOOM
/
mode manually.
16:9
This uniformly stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fi ll the wide TV
screen.
• For 16:9 aspect ratio pictures that have been
squeezed into a normal picture (4:3 aspect ratio),
use the 16:9 mode to restore the picture to its
original shape.
4:3
Use to view a normal picture (4:3 aspect ratio) as this
is its original size.

Panoramic

This stretches the left and right sides of a normal
picture (4:3 aspect ratio) to fi ll the screen, without
making the picture appear unnatural.
The top and bottom of the picture are slightly cut off.
14:9
This zooms up the wide picture (14:9 aspect ratio) to
the upper and lower limits of the screen.

Cinema

This zooms up the wide picture (16:9 aspect ratio) to
the full screen.
English - 28 -
19.03.2010 16:33:14 19.03.2010 16:33:14