Table des Matières
Publicité
UK
•
Elektromotoren over-
•
ophedes.
D
•
NL
•
Maskinen virker ikke,
•
F
selv om den er tilko-
blet.
•
E
P
•
Det er vanskeligt at
•
føre arbejdsemnet i en
ret linie langs savklin-
I
gen og savskæret er
uregelmæssigt.
S
•
Rundsaven støjer
•
og/eller går meget ure-
gelmæssigt.
SF
Rengøring
N
Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug en blød klud, der er vædet i sæbevand til
at fjerne hårdnakket snavs. Brug ingen opløsningsmidler, så som benzin, alkohol, ammo-
DK
niak, osv. Den slags stoffer beskadiger kunststofdelene.
Udskiftning af kulbørster
Fig. E
•
Fjern skruerne (1).
•
Træk kulbørsterne (2) ud fra rundsaven og undersøg dem for slitage.
•
Sæt kulbørsterne tilbage i de forhåndenværende holdere.
•
Kontroller, at kobberkontakten på kulbørsterne er i god kontakt med kobberdelen i
børsteholderen.
•
Sæt skruerne (1) i igen og stram dem godt.
Efter mange driftstimer kan kulbørsterne være slidt. Derfor skal kulbørsterne
kontrolleres regelmæssigt efter hver 30 driftstimer. Hvis kulbørsterne er kortere
end 4 mm, skal de udskiftes med nye.
Smøring
Maskinen behøver ingen ekstra smøring.
106
Motoren overbelastes,
•
Sav i et lavere tempo
fordi der saves for
og lad motoren køle af.
store arbejdsemner.
Motoren er defekt.
•
Kontakt venligst serv-
iceadressen på garanti-
beviset.
Fejl i netledningen.
•
Kontrollér netledningen
for brud.
Afbryderen er defekt.
•
Kontakt venligst serv-
iceadressen på garanti-
beviset.
Savklingen er bøjet
•
Udskift savklingen.
eller sløv.
Kulbørsterne er slidte.
•
Kontakt venligst serv-
iceadressen på garanti-
beviset.
Danger
a) Keep hands away from cutting area and the blade. Keep your second hand on auxiliary
handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.
b) Do not reach underneath the workpiece. The guard cannot protect you from the blade
below the workpiece.
c)
Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
d) Never hold piece being cut in your hands or across your leg. Secure the workpiece to a
stable platform. It is important to support the work properly to minimize body exposure,
blade binding, or loss of control.
e) Hold power tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will also
make exposed metal parts of the power tool "live" and shock the operator.
f)
When ripping always use a rip fence or straight edge guide. This improves the accuracy of
cut and reduces the chance of blade binding.
g) Always use blades with correct size and shape (diamond versus round) of arbour holes.
Blades that do not match the mounting hardware of the saw will run eccentrically, causing
loss of control.
h) Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were
specially designed for your saw, for optimum performance and safety of operation.
Causes and operator prevention of kickback
•
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an
uncontrolled saw to lift up and out of the workpiece toward the operator;
•
When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and
the motor reaction drives the unit rapidly back toward the operator;
•
If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade
can dig into the top surface of the wood causing the blade to climb out of the kerf and jump
back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and
can be avoided by taking proper precautions as given below.
a) Maintain a firm grip with both hands on the saw and position your arms to resist kickback
forces. Position your body to either side of the blade, but not in line with the blade. Kickback
could cause the saw to jump backwards, but kickback forces can be controlled by the
operator, if proper precautions are taken.
b) When blade is binding, or when interrupting a cut for any reason, release the trigger and
hold the saw motionless in the material until the blade comes to a complete stop. Never
attempt to remove the saw from the work or pull the saw backward while the blade is in
motion or kickback may occur. Investigate and take corrective actions to eliminate the
cause of blade binding.
c)
When restarting a saw in the workpiece, centre the saw blade in the kerf and check that
saw teeth are not engaged into the material. If saw blade is binding, it may walk up or
kickback from the workpiece as the saw is restarted.
d) Support large panels to minimise the risk of blade pinching and kickback. Large panels
tend to sag under their own weight. Supports must be placed under the panel on both
sides, near the line of cut and near the edge of the panel.
Ferm
Ferm
GB
D
NL
F
E
P
I
S
SF
N
DK
07
Publicité
Table des Matières
