Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4.1 ON/STANDBY MODE
In "Standby" mode the LCD displays the Stan-
dby icon
, the hour and day of the week.
All the operating modes are suspended ("Pilot
Wire" included), but the appliance is powered
and waiting for command reception.
To turn on or off the appliance, press the "Standby"
key. The towel warmer turns on in the previously
selected operating mode and emits a beep.
In "Chrono" mode the display shows the time, in the
other modes the temperature setting is displayed.
The entry into "Standby" mode is signalled by me-
ans of a double beep, the exit from "Standby" mode
by means of a long beep.
TURNING ON FOR THE FIRST TIME :
After inserting the batteries, set the year, month, day of the week and
time. Adjust the day of the week by using the "+" and "-" keys (1=MON,
2=TUE,...7=SUN), then confirm by pressing the "Mode" selection key.
The hour starts flashing. In the same way, adjust the hour by using the
"+" and "-" keys and confirm with "Mode" selection key. Repeat the
same procedure for the minutes. The year of start is 2021.
4.2 OPERATING MODES
The appliance provides 6 operating modes which allow the
user to heat the environment in the most suitable way with
respect to his needs.
Press the "Mode" selection key to select the
desired operating mode. An icon on the LCD
will show the selected operating mode.
Pilot Wire
Night/Eco
Chrono
PILOT WIRE
The temperature depends on the "Pilot Wire"
command.
All "Pilot Wire" commands are enabled.
COMFORT
The "Comfort" temperature corresponds to the
temperature desired by the user.
All "Pilot Wire" commands are disabled.
NIGHT/ECO
The "Night/Eco" mode keeps a comfortable tempe-
rature with a reduced energy consumption.
All "Pilot Wire" commands are disabled.
Comfort
Anti-Freeze
Energy Saving
17
ANTI-FREEZE
In "Anti-Freeze" mode, the temperature set point is
fixed at 7 °C. The appliance starts heating automati-
cally when the room temperature drops below 7 °C.
All "Pilot Wire" commands are disabled.
CHRONO
In this mode, you can select one of the three preset
chrono-thermostat programs or the custom pro-
gram. The latter lets you set a daily and weekly pro-
gram with two temperature levels ("Comfort" and
"Night/Eco"). All "Pilot Wire" commands are disabled.
ENERGY SAVING
This mode reduces the appliance's energy consum-
ption when the room is left unoccupied. Tempera-
ture is fixed at 17 °C.
All "Pilot Wire" commands are disabled.
When the icon
ing element is on.
4.2.1 PILOT WIRE
To activate the "Pilot Wire" mode:
Press the "Mode" selection key until the icon
appears on the LCD.
Users can only set the "Comfort" temperature
on the appliance.
Select the desired temperature set point by
using the "+" or "-" keys.
The home must be fitted with an automation system suppor-
ting this type of technology. In this case, correct transmis-
sion of the programming commands can be verified using
the following diagram according to the mode set:
Night/Eco
Mode
Comfort
(Comfort
Anti-Freeze Standby
-3,5 °C)
Signal to be
transmitted
Voltage
between
0 volt
230 volt
Pilot Wire and
Negative
neutral wires
The icon showing the mode selected on the control unit
(Standby, Comfort, Night/Eco, Anti-Freeze) is displayed to-
gether with the
icon.
If the Pilot Wire programmer is not connected, "Comfort" ope-
rating mode is selected automatically.
is displayed on the LCD, the heat-
Comfort
Comfort
-1 °C
-2 °C
230 volt For
230 volt For
115 volt
115 volt
an interval
an interval
Positive
of 3 s
of 7 s
GB
Publicité
Table des Matières
