Maintenance; Troubleshooting; The Appliance Does Not Switch On; Dust Coming Out During Vacuuming - Fimap FV9 Manuel D'utilisation Et D'entretien

1. Make sure the main switch is in the "0" position; if it isn't, press
the button (Fig. 12).
2. Remove the vacuum nozzle from the lid by rotating it anti-
clockwise (Arrow B in Fig. 13).
3. Remove the lid (1) from the vacuum tank by releasing the hooks
on the sides of the tank itself (Arrow A in Fig. 14).
4. If necessary, replace the collection bag (3) (Arrow A in Fig. 15).
5. Remove the fabric filter (2) from the appliance (Arrow A in Fig.
16)and clean it with neutral detergent and warm water (attention:
wait for it to dry before putting it back in the appliance).
6. Place the lid (1) on the vacuum tank (Arrow B in Fig. 14) and
fix it in place by means of the hooks on the sides of tank itself.
7. Remove the vacuum motor support (9) from the appliance by
releasing the hooks on the sides of the tank itself (Arrow B in
Fig. 17).
12
2
A B
16

THE APPLIANCE DOES NOT SWITCH ON

If the appliance does not switch on, proceed as follows:
1. Place the main switch on "I".
2. Check the plug on the power cable of the appliance has been
well inserted in the mains socket. If it hasn't, connect it properly.
3. Make sure that the electrical specifications of the appliance
correspond to the electrical specifications of the power supply
network, check the technical information on the serial number
plate.

DUST COMING OUT DURING VACUUMING

If dust emerges while you are using the appliance, check the
following:
1. Check the vacuum hose is properly connected to the nozzle on
the collection tank lid (if it isn't, insert it correctly).
2. Check that the vacuum hose is connected properly to the
accessory that is being used, if it is disconnected, connect it

THE VACUUM CAPACITY IS INSUFFICIENT

If the vacuum capacity is insufficient, proceed as follows:
1. Check the vacuum hose is properly connected to the nozzle on
the collection tank lid (if it isn't, insert it correctly).
2. Check that the vacuum hose is connected properly to the
accessory that is being used, if it is disconnected, connect it
correctly.
3. Check that there is nothing obstructing the vacuum hose, if there
is, remove it.
4. Check that there is nothing obstructing the vacuum chamber of
the accessory being used, if there is, remove it.
5. Make sure the collection bag isn't full (replace it if necessary).

MAINTENANCE

B
A
13
A
B
9
17

TROUBLESHOOTING

19
8. Remove the vacuum motor filter (10) from the appliance (Arrow
A in Fig. 18)and clean it with neutral detergent and warm water
(attention: wait for it to dry before putting it back in the appliance).
9. Place the vacuum motor support (9) below the vacuum tank and
fix it in place by means of the hooks on the sides of tank itself
(Arrow A in Fig. 17).
10. Remove the protection grille (11) from the front of the tank (Arrow
A in Fig. 19).
11. Remove the exhaust air filter (12) from the appliance and clean
it with neutral detergent and warm water (attention: wait for it to
dry before putting it back in the appliance).
Place the protection grille on the front of the appliance and push it to
fix it to the tank (Arrow B in Fig. 19).
A
B
1
14
A B
10
18
4. Make sure the power cable isn't damaged. If it isn't in perfect
condition, do not use the appliance and contact an authorised
assistance centre immediately.
correctly.
3. Make sure the collection bag isn't full (replace it if necessary).
4. Check the collection bag is correctly positioned.
5. Check that the collection tank lid is properly positioned.
6. Make sure the fabric filter isn't dirty or damaged (clean or replace
it as necessary).
7. Make sure the vacuum motor filter isn't dirty or damaged (clean or
replace it as necessary).
8. Make sure the exhaust air filter isn't dirty or damaged (clean or
replace it as necessary).
9. Check that the collection tank lid is properly positioned.
A B
3
15
12
A
11
19
B