Symbols And Their Meaning; Product Description And Specifications; Intended Use; Product Features - Bosch GTA 3800 Professional Notice Originale

the safe and steady machining of the workpiece cannot
be guaranteed.
Do not overload the saw stand or climb or stand on it.
u
Overloading or standing on the saw stand can raise its
centre of gravity, causing it to tip over.
Ensure that all screws and connecting pieces are
u
tightly fastened during transport and when carrying
out work. The holder sets for the power tool must al-
ways be securely locked. Loose connections can cause
instability and inaccurate sawing.
Only install and remove the power tool when it is in
u
the transport position (for information on the trans-
port position, also refer to the operating instructions
for the relevant power tool). Otherwise the power tool
may have an such unfavourable centre of gravity that you
will not be able to hold onto it securely.
Operate the power tool fastened to the holder set only
u
on the saw stand. Without the saw stand, the holder set
with the power tool is not secure and can tilt.
Ensure that long and heavy workpieces do not unbal-
u
ance the saw stand. The free end of long and heavy
workpieces must have something placed underneath it or
be supported.
When pushing together or pulling apart the saw stand,
u
do not put your fingers near the points of articulation.
There is a risk of fingers being crushed.
Symbols
The following symbols may provide you with important in-
formation about the use of your saw stand. Please take note
of these symbols and their meaning. Knowing what these
symbols mean will help you to use your saw stand more ef-
fectively and more safely.

Symbols and their meaning

The maximum load bearing capacity
(power tool + workpiece) of the saw
250
stand is 250 kg.
kg
Product description and
specifications

Intended Use

The saw stand is intended for holding the following Bosch
benchtop saws (stand 2021.03):
– GCM 8 S (3 601 L16 0..)
– GCM 8 SJ (3 601 L16 2..)
– GCM 800 S (3 601 L16 1..)
– GCM 80 SJ (3 601 M19 0..)
– GCM 800 SJ (3 601 M19 0..)
– GCM 8000 SJ (3 601 M19 0..)
– GCM 8 SJL (3 601 M19 1..)
Bosch Power Tools
– GCM 8 SDE (3 601 M19 2..)
– GCM 10 J (3 601 M20 2..)
– GCM 10 S (0 601 B20 5..)
– GCM 10 SD (0 601 B22 5..)
– GCM 10 GDJ (3 601 M27 0..)
– GCM 10 X (3 601 M15 0..)
– GCM 10 MX (3 601 M29 0..)
– GCM 12 SE (0 601 B23 5..)
– GCM 12 JL (3 601 M21 1..)
– GCM 12 MX (3 601 M21 1..)
– GCM 12 SDE (3 601 M23 1..)
– GCM 12 GDL (3 601 M23 6..)
– GCM 216 (3 601 M33 0..)
– GCM 350-254 (3 601 M22 6..)
– GCM 18V-216 (3 601 M41 0..)
– GCM 18V-305 GDC (3 601 M43 0..)
– GTM 12 (3 601 M15 0..)
– GTM 12 JL (3 601 M15 0..)
Selected mitre saws from other manufacturers can likewise
be installed.
The saw stand and power tool are intended for cutting
boards and profiles.

Product Features

The numbering of the components shown refers to the illus-
trations on the graphics pages at the beginning of the
manual.
(1) Workpiece support
(2) Table extension
(3) Table extension locking knob
(4) Holder set
(5) Locking knob for roller support height adjustment
(6) Workpiece support locking knob
(7) Roller support
(8) Length stop
(9) Height-adjustable foot
(10) Carrying handle
a)
(11) Transport stop
a)
(12) Transport wheels
(13) Height-adjustable support leg of the table exten-
a)
sion
(14) Socket spanner (13 mm)/hex key (4 mm)/cross-
headed screwdriver
(15) Locking pin
(16) Release button
(17) Holder set locking lever
(18) Movable nut
(19) Power tool fastening set
English | 15
1 609 92A 6JA | (24.08.2021)