Standard Accessories; Prior To Operation - Hitachi Koki C 12RSH2 Mode D'emploi

English
SPECIFICATIONS
Bevel
Max. Cutting
Capacity
Height × Width
Compound
Saw Blade Dimensions (oD × iD × Thickness)
Miter Cutting Angle
Bevel Cutting Angle
Compound Cutting Angle
Voltage (by areas)*
Power Input*
No-Load Speed
Machine Dimensions (Width × Depth × Height)
Weight (Net)
Laser Marker
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

○ 305 mm TCT Saw blade (mounted on tool) ...................1
○ Dust bag .......................................................................1
○ 17 mm Box wrench .......................................................1
○ Vise Assembly ..............................................................1
○ Holder ...........................................................................1
○ Side Handle (mounted on tool) .....................................1
○ Sub Fence (mounted on tool) ........................................1
Standard accessories are subject to change without notice.
APPLICATION
Cutting various types of aluminium sash and wood.

PRIOR TO OPERATION

CAUTION
Make all necessary adjustments before inserting the
plug in the power source.
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
Do not use with direct current, or transformers such as
boosters. Doing so may result in damage or accidents.
2. Power switch
Ensure that the power switch is in the OFF position. If the
plug is connected to a receptacle while the trigger switch
is in the ON position, the power tool will start operating
immediately, inviting serious accident.
0°
Miter 45°
Left 45°
Right 45°
Bevel (Left) 45° + Miter (Left) 45°
Bevel (Left) 45° + Miter (Right) 31°
Bevel (Right) 45° + Miter (Right) 45°
Bevel (Right) 45° + Miter (Left) 31°
Bevel (Left) 0° – 45°
Bevel (Right) 0° – 45°
Maximum output
(Iambda)
Laser medium
34
305 mm × 30 mm × 2.3 mm
Right 0° – 57°, Left 0° – 45°
Right 0° – 45°, Left 0° – 45°
Miter (Left) 0° – 45°, (Right) 0° – 31°
Miter (Right) 0° – 45°, (Left) 0° – 31°
110 V
655 mm × 890 mm × 724 mm
Po<0.4 mW Class 1M Laser Product
3. Extention cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Remove all packing
connected to the tool before attempting to operate
it.
5. Releasing the locking pin (Fig. 3)
When the power tool is prepared for shipping, its main
parts are secured by a locking pin.
Move the handle slightly so that the locking pin can be
disengaged.
During transport, lock the locking pin into the gear case.
6. Attach the dust bag to the main unit (Fig. 1)
7. Installation (Fig. 4)
Ensure that the machine is always fi xed to bench.
Attach the power tool to a level, horizontal work bench.
Select 8 mm diameter bolts suitable in length for the
thickness of the work bench.
Bolt length should be at least 40 mm plus the thickness
of the work bench.
For example, use 8 mm × 65 mm bolts for a 25 mm thick
work bench.
8. Base holder adjustment (Fig. 5)
Loosen the 6 mm bolt with the supplied 10 mm box
wrench. Adjust the base holder until its bottom surface
contacts the bench or the fl oor surface.
After adjustment, fi rmly tighten the 6 mm bolt.
9. Check to see that the lower guard operates
smoothly
105 mm × 312 mm
105 mm × 220 mm
68 mm × 312 mm
43 mm × 312 mm
68 mm × 220 mm
68 mm × 265 mm
43 mm × 220 mm
43 mm × 265 mm
230 V
1520 W
4000 min
–1
27 kg
650 nm
Laser Diode
materials attached or