Hilti DD 130 Mode D'emploi page 23

Masquer les pouces Voir aussi pour DD 130:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 34
Nominal no-load speed 1
2
3
Max. permissible water supply pressure:
Dimensions (L×W×H):
Weight as per EPTA-Procedure 01/2003:
Weight drill stand
Radio and television interference suppression
Interference immunity:
Protection class as per EN 60745 and IEC 60745:
Drilling depth:
-NOTE-
The vibration emission level given in this information sheet has been measured in accordance with a standardised
test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assess-
ment of exposure. The declared vibration emission level represents the main applications of the tool. However if
the tool is used for different applications, with different accessories or poorly maintained, the vibration emission
may differ. This may significantly increase the exposure level over the total working period. An estimation of the
level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working peri-
od. Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the
tool and the accessories, keep the hands warm, organisation of work patterns.
Noise and vibration information (measured in accordance with EN 60745):
Typical A-weighted noise power level (L
Typical A-weighted noise emission pressure level (L
For the given sound power level as per EN 60745, the tolerance is 3 dB.
Wear ear protection!
Triaxial vibration information (measured in accordance with 60745-2-1 at the grips and in accordance with
EN 61029 at the spider wheel)
Triaxial vibration values (vibration vector sum) EN 60745-2-1 (hand-held)
Vibration a
h DD
Uncertainty K
Triaxial vibration values (vibration vector sum) EN 61029, DD 130 rig (on drill stand)
Vibration a
h DD
Uncertainty K
Information for the user in accordance with EN 61000-3-11:
Switching on the tool may cause a brief voltage drop. Under unfavourable conditions in the mains supply, this
may cause interference to other appliances. No interference is to be expected when the mains supply has an
impedance of < 0.15 ohms.
* The tool is available in versions for various nominal voltages. Please refer to the rating plate for information on
the nominal voltage and nominal current rating of the applicable tool.
Right of technical changes reserved
18
Printed: 08.07.2013 | Doc-Nr: PUB / 5069520 / 000 / 01
st
gear
nd
gear
rd
gear
):
wA
Drilling into concrete
(with water supply)
5 m/s
2
1.5 m/s
2
Drilling into concrete
(with water supply)
3.5 m/s
2
1.5 m/s
2
780 /min
1400 /min
2600 /min
(Change gear only when rotation has stopped.)
6 bar (In the event of higher water pressure, a
pressure reduction valve must be fitted at the building
site connection.)
515×114×170 mm
7.3 kg
13.1 kg
as per EN 55014-1
as per EN 55014-2
Protection class I (earthed)
max. 430 mm (730 mm with extension)
100 dB (A)
):
89 dB (A)
pA
Drilling into sand-lime-
block (HDMU, dry)
6 m/s
2
1.5 m/s
2
Drilling into sand-lime-
block (HDMU, dry)
Drilling into sand-lime-
block (PCM, dry)
11 m/s
2
2.5 m/s
2
Drilling into sand-lime-
block (PCM, dry)

Publicité

Table des Matières
loading

Table des Matières