Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Vent system chart - 0 ft (0 m) to 10 ft (3.0 m)
No. of
0 ft
1-5 ft
turns or
(0 m)
(0.3-1.5 m)
elbows
0
120 ft
105 ft
(36.6 m)
(32.0 m)
1
110 ft
95 ft
(33.5 m)
(29.0 m)
2
100 ft
85 ft
(30.5 m)
(25.9 m)
3
90 ft
75 ft
(27.4 m)
(22.9 m)
4
80 ft
65 ft
(24.4 m)
(19.8 m)
5
70 ft
55 ft
(21.3 m)
(16.8 m)
Vent system chart - 11 ft (3.4 m) to 25 ft (7.6 m)
No. of
11-15 ft
16-20 ft
turns or
(3.4-4.6 m)
(4.9-6.1 m)
elbows
0
75 ft
60 ft
(22.9 m)
(18.3 m)
1
65 ft
50 ft
(19.8 m)
(15.2 m)
2
55 ft
40 ft
(16.8 m)
(12.2 m)
3
45 ft
30 ft
(13.7 m)
(9.1 m)
4
35 ft
20 ft
(10.7 m)
(6.1 m)
5
25 ft
10 ft
(7.6 m)
(3.0 m)
Install Vent System
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around
exhaust hood.
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust
hood with 4" (10.2 cm) clamp.
6-10 ft
Length of flexible metal vent
(1.8-3.0 m)
90 ft
(27.4 m)
80 ft
(24.4 m)
70 ft
Length of rigid metal vent
(21.3 m)
60 ft
(18.3 m)
50 ft
(15.2 m)
40 ft
(12.2 m)
21-25 ft
Length of flexible metal vent
(6.4-7.6 m)
45 ft
(13.7 m)
35 ft
(10.7 m)
25 ft
Length of rigid metal vent
(7.6 m)
15 ft
(4.6 m)
5 ft
(1.5 m)
0 ft
(0 m)
3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in
"Plan Vent System." Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape,
screws or other fastening devices that extend into the interior of the vent to secure vent.
Install Leveling Legs
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
1. To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place
cardboard under the entire back side of the dryer.
2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on
the cardboard. See illustration.
3. Examine the leveling legs. Find the diamond marking.
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the
diamond marking is no longer visible.
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.
Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.
Leave enough room to connect the exhaust vent.
Connect Vent
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to
existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust
outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a
4" (10.2 cm) clamp.
2. Move dryer into its final location. Do not crush or kink vent.
3. (On gas models) Check that there are no kinks in the flexible gas line.
4. Once the exhaust vent connection is made, remove the corner posts and cardboard.
17
Publicité
Table des Matières
Dépannage
