Connecting The Cables; Charging The Battery - Garmin Portable Ice Fishing kit Instructions D'installation

Peak transmit power
Operating voltage
Operating temperature range*
Storage temperature range
Material
Maximum range**
Frequency
Fuse rating
*When the transducer is used out of the water, the transducer
monitors the internal temperature and suspends operation until
the temperature returns to the operating range.
**Dependent upon transducer placement, water salinity, bottom
type, and other water conditions.
Assembling the Portable Mount
You need a Phillips screwdriver to assemble the portable mount.
1
Insert the handle into the two openings on the portable
mount base .
2 Secure the handle to the base using the two longer machine
screws and two nuts
3
Align the device mount over the hole pattern that matches
your device mount.
NOTE: A bail mount is included in some packages. If a
mount is not included, use the mount from your chartplotter
or fishfinder and the screws included in this package.
4 Secure the device mount to the base using the included
shorter machine screws
NOTE: Do not use the self-threading screws included with
the chartplotter. Only use the screws included with this
portable kit.
Installation Instructions
48 W
From 10 to 35 Vdc
From -10 to 40°C (from 14 to
104°F)
From -40 to 70°C (from -40 to
158°F)
ASA plastic
91.4 m (300 ft.)
417 kHz
4.0 A mini 32 Vdc
.
.
5
Screw the bail-mount knobs into the sides of the cradle.
6
Place the cradle into the bail mount and tighten the knobs.

Connecting the Cables

Ensure that you connect the correct spade connector to the
correct battery terminal. Damage to the battery or device, or
bodily harm may occur if the device is improperly connected to
the battery.
The bundled version contains the all-in-one power cable to
connect the necessary items in the bundle to the battery. The
non-bundled portable kit contains two power cables.
• The all-in-one power cable provides connections for the
threaded 4-pin power connector on the ECHOMAP
gray bare wire connectors for the Panoptix PS22 transducer,
battery charger adapter to connect the battery to the wall
charger, and spade connectors to the battery.
• The simple power cable, included only in the non-bundled kit,
provides a 4-pin power cable to connect a compatible device
to the battery.
1
Select the power cable and transducer cables to use with
your device and transducer.
2
Connect the power cable and transducer cables to the device
bracket.
3
Connect the Panoptix PS22 to the gray bare wire connectors
on the power cable. Connect the red wire on the power cable
to the red wire on the device, and connect the black wire on
the power cable to the black wire on the device.
4 Slide the red spade connector onto the positive (red) terminal
on the battery.
5 Slide the black spade connector onto the negative (black)
terminal on the battery.

Charging the Battery

Ensure that you connect the correct spade connector to the
correct battery terminal. Damage to the battery or device, or
bodily harm may occur if the device is improperly connected to
the battery.
You should always use the all-in-one cable to charge the
battery.
1
If you are using the simple power cable, disconnect the
spade connectors from the battery.
TIP: When using the all-in-one power cable with your unit,
you do not need to disconnect the power cable spade
connectors.
2
Connect the red and black spade connectors from the all-in-
one cable onto the corresponding battery terminals.
3
Connect the all-in-one cable to the wall charger.
4
Connect the wall charger to the wall outlet.
The light on the wall charger is solid orange when the battery is
charging. It takes about 8 to 10 hours in a room-temperature
environment to fully charge a fully discharged battery. When the
light is solid green, the battery is fully charged.
Placing the Portable Mount in the Bag
After you have assembled the portable mount, you can place it
in the bag, which makes it easier to carry and protects it from
the elements. The bag contains loops that allow you to tether
the bag as needed.
1
Slide two of the included hook and loop straps through the
narrow slots beside the battery compartment.
2
Place the battery into the battery compartment under the
handle.
CAUTION
™
CAUTION
device,
3