Declaration Of The Manufacturer; Quick Start - NEC AccuSync LCD73VM Manuel Utilisateur

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S
POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK • DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage
within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any
kind of contact with any part inside this unit.
This symbol alerts the user that important literature
concerning the operation and maintenance of this
unit has been included. Therefore, it should be read
carefully in order to avoid any problems.
Contents
Audio
Cable
CD-ROM
User's Manual
Power Cord Cable Holder
Base Stand

Quick Start

Stand
Locking Tabs
Base
Figure S.1
Figure A.1
Macintosh Cable
Adapter (not included)
Figure B.1
01_English
WARNING
We hereby certify that the colour monitors AccuSync LCD73VM
(L175GZ)/AccuSync LCD93VM (L195GY) are in compliance with
Council Directive 73/23/EEC:
Council Directive 89/336/EEC:
Your new NEC AccuSync LCD monitor box* should contain the
following:
• AccuSync LCD monitor with tilt base
• Audio Cable
• Power Cord
• User's Manual
• CD-ROM
• Base Stand
• Cable Holder
AccuSync LCD monitor
* Remember to save your original box and packing material to
Captive type (Video signal
transport or ship the monitor.
cable is connected)
To attach the Base to the LCD Stand:
1. Insert the front of the LCD stand into the holes in the front of the
Base (Figure S.1).
2. Attach the Base to the Stand. The locking tab on the Base should
fit into the hole on the back of the Stand (Figure S.1).
To attach the Cable Holder:
Cable Holder
1. Attach the Cable Holder on to the Base. Insert the hooks on the
Cable Holder into the holes at the back of the Stand and slide the
Cable Holder downward into place (Figure S.1).
NOTE:
To attach the AccuSync LCD monitor to your system, follow these
instructions:
1. Turn off the power to your computer.
2. For the PC with Analog output: Connect the 15-pin mini D-SUB
signal cable connected with the monitor to the connector of the
display card in your system (Figure A.1). Tighten all screws.
Figure A.2
For the Mac: Connect the MultiSync Macintosh cable adapter
(not included) to the computer. Attach the 15-pin mini
D-SUB signal cable to the MultiSync Macintosh cable adapter
AUDIO INPUT
(Figure A.2). Tighten all screws.
NOTE:
3. Connect the Audio Cable to the appropriate connector on the
back of the monitor (Figure B.1). Connect the Headphone
(not included) to the appropriate connector at the front of the
Cable holder monitor (Figure C.1).
4. Connect the power cord to the power outlet. Place the Video
Connect to Computer
Signal Cable and power cord to the Cable holder (Figure B.1).
audio output
English-1
1

Declaration of the Manufacturer

and marked with
– EN 60950-1
– EN 55022
– EN 61000-3-2
NEC Display Solutions, Ltd.
– EN 61000-3-3
4-13-23, Shibaura,
– EN 55024
Tokyo 108-0023, Japan
Please confirm that the tabs are completely secure.
Some Macintosh systems do not require a Macintosh cable
adapter.
16/5/06, 9:11
Minato-Ku